66568600890 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from Pine, CO
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from SAINT JOHNS, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light in microwave
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from Libertyville, IL
- Parts Used:
- W10245183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Loud buzzing noise and no heat.
PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Patterson, NY
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken vent grille
Simply removed two screws to remove the old vent grille and replaced it with the new grille. I was also very pleased with the assistance I received from the service rep. I had ordered the wrong grille. I called the PartSelect help number and the rep walked me through the product return process, then found the correct part and ordered it. I had the replace 3 - 4 days later. The rep was very polite and patient during the whole process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily C from Brandon, MS
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped the glass cooking tray and it broke in half
Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!
E. Robinson
E. Robinson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SM from JAMESTOWN, RI
- Parts Used:
- 6800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
On-door water/ice dispenser lights failed, paddles did not work to dispense
It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAN ANTONIO, TX
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Vent grill replacement
Unscrewed 4 different screws, replaced the vent & returned screws. Ack to original positions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monty from Mansfield, TX
- Parts Used:
- W10642989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace turntable motor
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from GULF BREEZE, FL
- Parts Used:
- 8183948
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old vent fell apart
Slipped in and screwed top on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from SIOUX FALLS, SD
- Parts Used:
- 8183948
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I took off the wrong way and Broke it
Took 4 Screw on top off...set bottom in first into slots ..pushed top in under the top of outside cover ...put Scews back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CENTENNIAL, CO
- Parts Used:
- W10435116
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Very Pleased with Parts Select replacement parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FRANKLIN, TN
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave vent cover broke as it was cleaned.
Bought a new one. Perfect match, easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from EXETER, NH
- Parts Used:
- W11252182
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the wheels came off
Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul
New one, ring that is. It was easy using the part from parts select
Thanks
Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Everett, WA
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The grill broke when removing it to clean
Unscrewed two screws, fit the grill into place and screwed in two screws.
Was this instruction helpful to you?
Thank you for voting!