JMV9186WS0 Jenn-Air Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Laura from Port St Lucie, FL
- Parts Used:
- W10435116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable coupling
Rep knew exactly what I needed when I described where the part should go on my microwave - price great - shipping great - installed in seconds. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Pine, CO
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from Libertyville, IL
- Parts Used:
- W10245183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Loud buzzing noise and no heat.
PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from SAINT JOHNS, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light in microwave
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from ARVADA, CO
- Parts Used:
- 4393799
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had broken the glass turn table.
I ordered another one and placed it inside the microwave. It works and fits perfectly. I received the order exactly as scheduled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from SUFFERN, NY
- Parts Used:
- W10709921
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb under the microwave burned out
Used a philips head screwdriver to remove one screw holding the light cover. Pulled out the old bulb and inserted the new one. Replaced the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LELIA W from MONTGOMERY, AL
- Parts Used:
- W10208631A, 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken turn plate.
Cleaned the interior of my microwave, cleaned the new plate and simply added to the turn area.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from OVERLAND PARK, KS
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulb
Husband replaced the bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon C from MEDFORD, OR
- Parts Used:
- W11252182
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave didn't have support ring when house was purchased.
Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARMELO from LOVETTSVILLE, VA
- Parts Used:
- W10709921
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both lights failed. Replaced with new bulbs.
Unscrew lens and direct access to surface light cavity. Removed old light bulbs and replaced with new bulbs. Reassembled lens cover and turned lights on successfully. Took less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily C from Brandon, MS
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped the glass cooking tray and it broke in half
Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!
E. Robinson
E. Robinson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CENTENNIAL, CO
- Parts Used:
- W10435116
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Very Pleased with Parts Select replacement parts
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Barnwell, SC
- Parts Used:
- W10269460
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave turn table turns with door open, light on when unit off and door shut, slamming the door restored normal operation for a while.
Based on other similar posted repairs, I purchased the bottom switch. Upon removing the control panel to replace the switch, I found the blue 22 gauge wire was broken at the spade terminal. This wire had been crimped to the terminal along with a 14 gauge wire. Apparently the force to crimp the thicker wire weakened the smaller wire at the terminal. I stripped the end of the small blue wire and reattached it to the thicker wire using a solder iron and solder. The repair fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from DRIPPING SPGS, TX
- Parts Used:
- W11661547
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
Changed out turntable motor
Was this instruction helpful to you?
Thank you for voting!