JMW9527DAB29 Jenn-Air Microwave - Instructions

I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.

OMG! I wish everything in life were so easy.....The cooking tray of our 15 year old microwave cracked and I swore it'd be impossible to find a replacement. That is until I discovered Partselect.com!!All I had to do was input the appliance brand and part I was looking for, and there is was. Thank you, Partselect.com!!

Removed 7 screws from microwave bottom panel. Panel swings down exposing the turntable motor. Replace motor. Replace the panel. I did not remove the micro wave or the range stove. It is a little difficult working over the stove but it can be done. It does save time. Turntable works o.k. no noise. Doing the job myself saved a $200 service call. On line instructions ,parts list and diagrams are very helpful.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

You have to remove the cover which in my case was a little more difficult because the unit is wall mounted and has a frame around it. That was the hard part. Once the mounting frame was removed, you can remove the cover and the light bulb is on the top right side of the unit. One screw removes it and the new one pops right in. Put the case back on reinstall it in the wall and voila...piece of cake.

you will a security socket T20. this unit was installed over oven, remove trim cover,remove screws holding unit in place,I used a helper to get the unit out, once out you have to remove all the screws holding the cover on,on two of the corners they use a security hex screw so you need a special socket for that. remove the door latch switch,take your time or you will break tab holding switch in. ask me how I know.but super glued broke piece in place and plugged wire back in.the new latch may have a second pin but look at old one and plug wires in the same way.the light bulb does not screw out so I had to purchase the entire unit.total cost under a $100.00 to do repair.

PART SELECT is excellent. I will use this source again. A repairman came after I ordered the parts. Perfect instructions. Wonderful help by phone.

I received my glass cooking tray so fast but when I try to put in the microwave did't fix was to big,I call you today to return and very nice lady help me and told me I need to call whirlpool and explain them and already order again thank so much for all your help you have very nice people in customer service. Thank you so much again. !!

Removed cover and installed light

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

hardest part was taking the microwave down off of the wall to gain access to the diode. Thought if was the transformer but ended up being just a blown diode. remove and replace and bench test. that part took 15 minutes . moral of the story don't boil water under the side of the microwave that holds the electric components.

We got a a carbon steel but and drilled out the stews and put in regular screws. We also had trouble getting the cover back on and ended putting 2 more screws on the left side which had none. The installation was the easiest part of the installation.

Just took the plate out the packaging & rinsed,dried and put in the oven. I was so happy I found it @partselect online& it came in the next day or two. Will definitely use them again. It was a fraction of the cost from local parts store.