JMV8208AAB Jenn-Air Microwave - Instructions

Pulled unit out, pried the bottom plate off the unit. Mine was not screwed in, but designed to be pried off, and then replaced. That was a surprise, but not very difficult. Unscrewed the motor, unplugged the electric connection, replaced it with new part . Replaced the bottom plate and tested the machine.

The power on the microwave went completely out when I went to use it, but there was no power failure for the house or neighborhood. We removed the microwave from above the oven. Took out the screws on the sides and back of the microwave and slid the top back. The line fuse was located on top unobstructed, NOT behind the button panel like some microwave models. As the appliance is over 20 years old the line fuse was quite old. It was really hard to pry it out of its holder and actually broke. I used a vacuum to suck up the dust and glass and it was easier to get out the ends once the middle broke. Popped the new line fuse in, slid the top back on, put in the screws and put the microwave back in its compartment above the stove. Good as new!! We were about to spend money on a new microwave, but thankfully I came across this site. So happy I did!!

This repair was really easy. The part that took the most time was taking it down from it's compartment above the oven and putting it back up there once repaired.

removed a dozen screws-discarded large cap-replaced diode-replaced a dozen screws(took longer to replace them than remove for some unknown reason). Microwave now works(wife happy).

Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

Remove from cabinetry, take cover off and had a very difficult time removing the plastic form that has the switched in. Replace the lowest of all the switches, and then again very difficult time getting the plastic form back in. Some of the plastic even broke during the process but not any that could prevent it from working as it did before. I had ordered a fuse, 2 packs of 2 switches as there are 3 switches but only had to use 1 to get it working again. Tested after switch install, put the cover back on and reinstalled in the cabinet.

Super Easy. I was able to find the part on your website.
The whole process was excellent.

Unscrewing the old one out, putting the new one in.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

Did have a difficult time getting the old bulb out as it broke off in the socket. We disconnected the microwave to retrieve the broken bulb with a needle nose tweezer and then installed the new bulb in seconds. The plate glass cover was then placed back. Ended up vacuuming the ceramic stovetop due to broken chips of old bulb when being retrieved. Thanks for the prompt arrival of the new bulb. Hope it will last as long as the other bulb of 5 yrs.

Install new rotating plate

I have tried MANY times to get the proper bulb from various hardware stores with varying degrees of success. My bulb seems to burn out often because we happen to have frequent power surges. This past time I was unable to get a bulb at the hardware store which would work at all. The bulb purchased specifically for this appliance, while very expensive INSTALLS PERFECTLY WITH EASE! Well worth the extra money.

Unplugged microwave, unscrewed cover, opened bulb package, without touching bulb and pushed into holder. Plugged in microwave and alas light worked. Screwed lid back in place.

Information provided on the web site by Part Select, were helpful and encouraging to select and buy the part needed to repair the appliance. No doubt, a skilled person having background in the repair of appliances should attend such repair job.