IRH32001 Inglis Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Foreclosed home: parts were missing
Having the correct model number helps:
Just place the parts in the microwave and it worked.
Just place the parts in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from summerville, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Light Bulb Replacement
Open compartment, installed bulb, closed compartment
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Maceo, KY
- Parts Used:
- 8169438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The microwave door would not stay latched, so it wouldn't come on.
The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Edwards, CO
- Parts Used:
- 4393777
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door cracked and the door handle fell off.
I removed the screws to the old handle and screwed on the new one
Was this instruction helpful to you?
Thank you for voting!
Light burnt out and door will not close properly
I had been dealing with a broken vent cover and burned out light for several months. I should have fixed it much sooner if I knew how easy it was. PartSelect.com had pictures of everything I needed and after reading the repair stories I was able to disassemble the pieces necessary and clean them before reinstalling. Very fast shipping also. The vent grille attaches easily with a couple screws. It's weakest point is the plastic tabs which will break and then gravity puts the grill in the doors ways. The light bulbs can be accessed with a hinged glass door (one screw) but be careful they are very fragil and can break off. If they do unplug your unit, get a pair of needle nose pliers and slowly unscrew the rest of the bulb. If you wanting room or you want to clean the grease off, I recommend removing the whole bottom cover from the microwave (7 scews and 2 wire harness clips).
Was this instruction helpful to you?
Thank you for voting!
Old light bulb popped and burned out and melded itself to the socket. Light bulb then broke off inside the socket. Socket cracked and broke when trying to dislodge broken light bulb.
Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.
Was this instruction helpful to you?
Thank you for voting!
Microwave would not heat
Removed microwave case and bad part was right there in plain sight attached to the magatron. Two screws and two wires and part replacement was done. Plugged in microwave and works perfect. Couldn't have been any easier. Thanks for the easy troubleshooting and parts suggestions on your site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARCY from CHARLOTTE, NC
- Parts Used:
- 8183948
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Critical grill pieces for attachment purposes broke when removing for cleaning
Wedged grill into open space and screwed in with existing screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Humberto L. from Hallandale, FL
- Parts Used:
- 8183948
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The opening was very tight
It was supposed to be a very easy replacement, but when inserted the legs in the bottom openings, the legs at the top didn't enter the opening.If insert first the top legs then the bottom legs could not go in. Tried to put a little force when turning grill to enter the top legs with the screws support. Finally very carefully put first the top legs, entering horizontally, and then giving a little push (forcing) the bottom legs in. This was not supposed to be this way, because I could had brake the bottom legs clip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Bloomingdale, IL
- Parts Used:
- 8183948
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Vent Grille fell off when opening door on microwave
Removed 2 screws that were holding broken plastic tabs. Lined up lower plastic tabs on new grille into slots, gently. Tipped forward to engage upper tabs into slots. You need to "gently" press the top into place to avoid breaking off the tabs! Replace 2 screws, and hand tighten with Phillips screwdriver. Easier to see what you're doing with the microwave door "open". I felt "accomplished" for a 70-year old Grandma.:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ferol from San Antonio, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burned out bulbs under the microwave/important light source for kitchen stove.
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.
Was this instruction helpful to you?
Thank you for voting!