RVM1625WD004 Hotpoint Microwave - Instructions

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

Removed the 1 inch plastic frame on inside of door, gave me access to 1 set of screws. The problem I encountered was, getting to the set that holds the handle to the door.I didn't realize the metal frame held the outside with flexible hooks, therefore once u snapped them off, the outside with the handle on it HIT the floor glass and all!
Fortunately it didn't break. Supporting the outside is most important.

took of cover removed switch and replaced with new one

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

I simply pulled the old coupler off the moter shaft after removing glass turntable plate. The coupler lifted right out since it was fractured. Luckily all peices came out attached. Typically you would need to remove the bottom access panel on the microwave and remove the turntable motor to install the new coupler. However you can simply snap off the extra plastic piece that is molded to the coupler to allow for an easy push down onto the shaft from the inside of the microwave cooking area where the coupler fits onto the moter. Piece of cake. I don't believe there is any danger in shortcutting this because the weight of the glass plate will hold it in place.

Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.

Pulled out broken one with fingers, put on new one with fingers, it did not have anything preventing it from just slipping on. Didn't need to take anything apart to install me part.

I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.

First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.

Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.