JE1160B General Electric Microwave - Instructions

I determined that one of the 4 micro switches that interface with the door was faulty. Ordered that part and replaced it. Had to remove the cover and front control panel (without removing any connections. Two philips screws hold the limit switch assembly to the bracket. After removing those screws, twist the whole switch assembly clockwise around the mounting frame and now you can remove the defective micro switch and replace it with a new one. This works for any of the 4 switches.

Was sent the wrong part but wanted a pizza so I installed it anyway and now the turntable turns a 6 rpm instead of 3 rpm. I figured that the part I ordered was no longer available and that was the best you could do for a replacement part. Replacement was easy- removed panel from bottom of microwave and filed the sharp edges from the side cutters, remove the one motor screw and motor. swapped the plug over and installed the new part. Replaced bottom panel, plugged in and cooked a pizza.

ordered the wrong part, (my mistake) new part took about 5 mins. no problem.

First remove tamper proof screws with vise - grips. Unplug capacitor ground out one side to discharge. Trouble shooting guide in a envelope in microwave, read it and did what it said. If 20 amp fuse is blown ( which it was ) replace primary and secondary switch and monitor switch. Switch assemble removes as a unit. Wires where hard to remove, you have to push on a release located on one side and pull to remove. Works great , only one switch was bad, but I did what the guide said. Draw a picture of wiring with color code so you do not mix up.

Ordering was simple, had pictures with descriptions so you have no problem finding the right part. Receive 3rd day after ordering. Motor Replacement was ever easy, remove screws holding bottom plate, unplug failed moter, remove mounting screws, remove failed motor - Install new motor and screws, plug in power cable - replace bottom pan, job done. As a side note, the original moter was 2-watts the replacement motor was 3-watts, more power means better motor, and this motor runs very quiet. Totally satisified.

just replace it

Understand the type of fasteners GE used in the appliance require a BRISTOL type screwdrive.....unfortunatley this tool is not a part of my tool chest.....after running my four letter vocabulary and the use of thin blade screwdrive a a small vise grip plier was able to get the little bugers out.....thank goodness there was only four.

It took two people because we have built-in unit. The power plug was in cabinet above.First had to remove front frame in cabinet with Phillips screwdriver. Removed microwave from cabinet box (be sure to wear gloves, edges are very sharp). Then unscrew outer shell of microwave - easy process. Easy task to remove bulb/socket piece. We ordered part from Part Select - friendly service and the price is the best. Even with minimal shipping costs, the local prices were more than double. Important, it is a bulb and socket part.

I simply lined it up with the grooves on the microwave floor. It fit and worked perfectly. It was easy and saved me the cost of a new microwave.

My husband burned the microwave by using alumifoil. It was working for a little while after that but next day, the microwave was completely off. He thought the thermostat was broken, ordered the part and replace it. It's fixed and working fine now. Someone mentioned that if you put the broken thermostat in the freezer, it will be reset and fixed. I tried that also. I wrap the thermostat and put it in the freezer for one day. Now it's working!! I didn't know about that before I ordered the part but it wasn't expensive at all. So now, we have extra thermostat!!

First you have to get the "security screws" out with a pliers or vise grips then it was a snap, just replace the screws with 1/4 drive screws for the next time you have to get in there !

I just took off the cover, located the magnetron, replaced it and slapped everything back together and since then everything's been working pretty good.

Simply remove the cover after unplugging the Microwave. The light is attached to a bracket and unplugs from the electrical system and then pops out. Replace with the new bulb and bracket, reattach the electrical connection and replace the cover. Less than 15 minutes. Just need a special star screwdriver bit with a hole in the middle to remove and replace the screws holding the cover to the frame.

After opening the case (the most difficult part of the job), tested the fuse (good) next in line on the power lead was the "flame sensor". With my ohmmeter it read open. The schematic noted that it opens at 212 degrees and closes at 32. Put it in the freezer for 15-20 minutes while I ordered a replacement. Upon rechecking, it had reset. Reinstalled it and everything works fine. I did receive the new one and it's on the shelf, just in case.

Remove bezel (4 Phillips sheet metal screws). Pull out unit and unplug from wall. Remove three sided steel cover (T15 or T20 safty bit required). Unclip double wire plug from base of lamp. Unclip and pull up on the lamp/bracket - discard. Push down new lamp/bracket, plug in wire socket to base of lamp/bracket. Replace steel cover and 4 'safety headed screws'. Lift unit, replug into wall socket. Insert into wall. Replace bezel and 4 Phillips sheet metal screws. Without the special "safety screw bit", this repair is impossible.