RVM1435C General Electric Microwave - Instructions

took off upper grille and touch pad and removed the old line fuse and replaced with a new fuse ...turned on it is working fine...sources of help: UTube and GE manuel

All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

Had trouble isolating the problem, so I had a repairman identify the problem, then I ordered the part and replaced it myself.

Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.

Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

The motor shaft was broken. This microwave is mounted over a stove. first unplug the microwave. I removed 6 screws from the bottom to gain access to the turntable motor. Remove single screw holding motor. Rotate motor to remove. unplug wiring plug from motor. Reverse procedure to install new motor. Note that spindle for turn table goes on from above and is indexed to motor.

I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

took of cover removed switch and replaced with new one

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????