JE1460B General Electric Microwave - Instructions

unplugged power
removed main black cover.
located part WB24X10047 and replaced

Part just snapped into place and wires were reattached.

Went on Youtube and pulled up how to fix a microwave.

Replaced the fuse. Result; did not fix the problem.

AFter I put the roller guide and glass cooking tray inside the microwave it still didn't spin. After check with the video, I was warned not to try to replace the motor which spins the tray, that there was a chance of electrical shock. I took the oven to my repair place and they made the repairs.

First I took out the screws holding the sides and back to the microwave. I discovered that the rotissereie motor was also damaged, but had an old GE microwave that had quit working-took out motor from other GE(motor was the same), installed motor in microwave, lined up pin to roller assy. and that was it!

After contacting GE support I realized the only interest they had in helping me was to recommend sending a $$$ technican to diagnose the problem. I decided to go to the Sears Parts select website.to see if others were experiencing the noise me microwave was making. After reading through others posting on the subject I decided to purchase the Synchronous Motor. While waiting for the part to come I decided to lubricate the hub of the spides that rotates the plate with white Lithium grease. After a couple of times utilizing the microwave noise went away so whn the part arrived at me home I put it in a drawer just incase I need it a some future date. Hope that someone else finds this information useful. "The Crafty Dodger in Houston"

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

Replace the fuses

Just like the directions said. Very simple.

Remove tray and rotating ring assembly. Turn the microwave onto the back. Locate the center plate and cut it loose with the side cutters. (Note: there are retaining slots on the opposite side) these slots hold the cover plate in place when reattaching. Use a magnetic phillips head screw driver so you don't drop the cover retaining screw. After cutting loose the cover, unplug the wires from the motor. (Note placement for correct reattachment). Remove 2 screws and remove old motor. Replace motor. Replace the screws and reattach the wires. Replace the cover (rotate so the prongs fit into the slots) tighten screw; you're done!!! I ordered the rotating ring, but I don't need it. Now I have an extra.

It was extremely easy. I put the microwave on my table upside down and could see the motor thru the holes in the bottom cover. It appeared as though the outside skin had to be removed to access the motor but after looking at it there is an access panel I did have to cut it loose. Not bolted on. There was a message stamped into the bottom case next to the panel that said to debur after panel is removed. So I cut it loose on 3 sides was able get to the one screw swap the motor and reinstall it in about 5 minutes. It works like new What an easy and quick repair. Thanks

Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!