JE2160W General Electric Microwave - Instructions

On the bottom of Microwave I cut the 6 clips holding the cover in place with side cutters. Removed the one screw holding motor in place. Un plugged it. Plugged in new motor, replaced screw. Filed off sharp points of clips. Slid cover tabs into slots, put screw in cover. Replaced parts inside oven, turned it on, it worked.
I did this twice. The first time the plug fell inside the housing and I had to turn the microwave over to fish it out. So when I received new part I left it plugged in. I should make it clear I am talking about the plug to the motor not the one to the microwave. Of course I unplugged that before I even moved the microwave. Thanks to another customer and his repair story because I was dreading the chore of dismantling the entire microwave to get to the turn table motor. He made it so easy. Thank you for having the part and great instructions.

We removed the glass circular plate of the microwave. We replaced the original roller guide with the new part. Then we placed the glass plate back in its place. Quick and simple.

Fast & easy. I was able to determine that this foot would work from the descriptions on online!! Thanks

I placed the new hot plate in the old microwave. It worked perfectly, and no tools needed

removed 3 screws from back took cover off pulled out socket pulled off terminal replaced bulb then reverse order back together. all while unplugged.

Went on line and saw the Video - very simple to follow - very easy to remove and install the new switch -- went like a breeze!

Removed old roller assembly and installed new roller assembly.

Take the four saftey torx screws off the back of microwave that hold the side panels on. There are no screws in the front. Just pick up the side panels a little and slide towards the back of microwave and it will come off. The magnetron is visible behind control panel. Unplug the magetron, take a 3/8 nut driver , remove the one bolt that holds it on , remove and replace with the new one. Plug the wire (it will only go one way) back up and replace cover.

Went well, very easy to change once the microwave was out of the wall. Sounds better than when it was new.

Light bulb repair was super easy once I got the out shell of the microwave off. The unanticipated problem was that I didn't realize the outer shell was secured with unusual "Security Torx" screws I have a couple star screw drivers but these were very unusual and could not find a proper screwdriver to remove them. I was able to force them lose with a small philips screwdriver and a pair of channel lock pliers. It took me quite a while to get the screws off this way but once I got them out and the outer shell off the microwave the light bulb replacement took less than 10 minutes. You should market the appropriate screwdriver to remove the outer microwave shell with any interior replacement parts.

Replacing the light bulb is easy and takes no more than 15-30 minutes. The light bulb is located behind the grill on the right hand side of the microwave as you face the microwave. To get to the bulb you have to remove the outside cover. On mine there were three screws that had a special head and required a special tool. That was a surprise! To work around that, since I did not have the tool, I used a pair of needle nose pliers to grip and turn the screw head. They came out easily. I replaced them with the same size Phillips head sheet metal screw when I put the cover back on.
1. Remove the screws that secure outside cover and take the cover off.
2. Locate the light bulb and unplug the power wire. It is a two prong plug that pulls off with little effort.
3. Remove the old light bulb. It is held in place by a plastic tab. Push the tab toward the outside of the base plate with a small screw drive or your finger and lift the base plate. The bulb will come out with the base.
4. Install the new bulb. Align the holes in the base of the new bulb with the tabs on the socket and put the bulb in place, ensuring the tab secures the bulb base in place.
5. Reconnect the power wire to the bulb.
6. Reinstall the outside cover.
7. The light should come on when you open the microwave door.

Remove bezel (4 Phillips sheet metal screws). Pull out unit and unplug from wall. Remove three sided steel cover (T15 or T20 safty bit required). Unclip double wire plug from base of lamp. Unclip and pull up on the lamp/bracket - discard. Push down new lamp/bracket, plug in wire socket to base of lamp/bracket. Replace steel cover and 4 'safety headed screws'. Lift unit, replug into wall socket. Insert into wall. Replace bezel and 4 Phillips sheet metal screws. Without the special "safety screw bit", this repair is impossible.

First remove tamper proof screws with vise - grips. Unplug capacitor ground out one side to discharge. Trouble shooting guide in a envelope in microwave, read it and did what it said. If 20 amp fuse is blown ( which it was ) replace primary and secondary switch and monitor switch. Switch assemble removes as a unit. Wires where hard to remove, you have to push on a release located on one side and pull to remove. Works great , only one switch was bad, but I did what the guide said. Draw a picture of wiring with color code so you do not mix up.

Understand the type of fasteners GE used in the appliance require a BRISTOL type screwdrive.....unfortunatley this tool is not a part of my tool chest.....after running my four letter vocabulary and the use of thin blade screwdrive a a small vise grip plier was able to get the little bugers out.....thank goodness there was only four.

I just took off the cover, located the magnetron, replaced it and slapped everything back together and since then everything's been working pretty good.