EMO2000C02CC General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Columbus, OH
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cooking tray cracked.
First I replaced the cracked cooking tray and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Divina from Grand Rapids, MI
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both under mount lights were burned out
Unscrewed bottom panel, then unscrewed light socket, then replaced with new socket and bulb. Reattached socket and panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from salmon, ID
- Parts Used:
- WB36X10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lens Was Not Sized To Fit And Was Left Extremely Sharp
Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florence from Lake Forest, IL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray cracked after only 4 months of use
Replacement tray was installed. It was larger than the original tray, but it fits in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from IRVINE, CA
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped and broke the cooking tray
New one arrived very quickly.
Right part. Right on time. Fit like it should.
Excellent service.
Right part. Right on time. Fit like it should.
Excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Clearwater, FL
- Parts Used:
- WB01X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lost screws for the covers on the lights over the cook-top
Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from LAUREL, MD
- Parts Used:
- WB6X486
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease Filters underneath microwave can not be cleaned. Must replace them.
Very easy repair to replace filters. Step 1: Note position of filter and which end is towards you and position of latch handle. Slide old grease filter away from you and forward until it drops out, Set it aside. Step 2: Take new filter and put in slot away (as you noted) from you then slide towards you until seated properly underneath microwave. Repeat steps for the second filter. It takes about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Fort Worth, TX
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Voorhees, NJ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
microwave turntable wouldn't turn
Wow! It really was as easy as everyone says. I ordered the part. It came overnight. I took out the 6 screws on the bottom of the microwave (AFTER unplugging the microwave of course), unscrewed the part and unplugged it, put in the new motor, plugged it in and screwed it in, and replaced the bottom screws. The only trouble I had, which really has nothing to do with this part or the repair, was that some of the screws on the bottom of the microwave were very difficult to replace as they didn't seem to line up with the holes beneath. I had a handyman coming to do some deck repairs and had him put those in. Ah well. I did MOST of it myself.
Stephanie, age 52
Stephanie, age 52
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Leesburg, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
NO light
.Thank You Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ina from Horn Lake, MS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor went out. Glass tray wouldn't rotate any longer
Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine J from Yuma, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive motor not working
There where five screws to remove to get the bottom off then two to release the motor from the housing pull the electrical supply cord out then reverse the process. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from DAVIE, FL
- Parts Used:
- WB06X10138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Turntable coupler became very charred and brittle and was sparking.
The old one was extremely difficult to remove, like it was ‘welded‘ in place. I had to crush and destroy it with vice grips in order to get it. it off. The new one would not go on unless I modified it by removing a “spur“ which prevented it from sitting flush with the bottom of the oven. All in all it took less than 25 minutes and it is now working well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SEASIDE, CA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Glass lens and two light bulbs replacements
My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.
Was this instruction helpful to you?
Thank you for voting!