JVM3670BF06 General Electric Microwave - Instructions

Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.

Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.

Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)

placed plastic ring under glass rotating plate in microwave

Received part installed in less than one minute, easy fix alignment of part in shaft pressing down into position

Using a phillips screwdriver, remove 7 screws from the unerpanel of the Spacesaver Microwave. The panel will swing down from the rear edge hinge, exposing the lights and the stirrer motor. Remove the electrical connector and two screws holding the motor in place and remove the motor. The stirrer inside the oven can then be removed if desired. Install the new motor in reverse order. Note rotate the stirrer inside the oven to align the motor shaft to facilitate assembly.

Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.

ordered part from partselect received in about 3-4 days removed 6 ea screws from lower panel , removed 1 ea screw holding motor in place, pulled wire receptacle loose from motor, threw old motor in trash, put new motor up into plastic tray rotating device turned motor to secure on one side and installed screw to hold motor reinstalled wire plug and panel ops ckd good about 15 minutes to do could have done it quicker but my eyes ain't what they use to be Very easy fix when you get the right part and I got it on the first order with partselect ......Thank You Very Much

ha to remove the bottom ,to get at the internal screws that held the drive motor. after disconnecting the power to the moter, i removed the two screws that held it in place. i installed thre new motor , reconnected the wire plug to motor . replaced the outer screws, and the project was done.

I removed the screws (7) around perimeter of bottom. Don't remove the middle screw as it holds some gizmo in place. Dropped down hinged bottom. Removed motor (2 screws and a plug) matched to picture on website and ordered.

2 days later, part arrived, installed, good to go.

Bill, Kentucky

Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

This is a GE Profile under-the-cabinet microwave oven that retails between $620-$720 new. I unscrewed 4 bolts to drop the oven from front-to-back, removed 3 screws on the old grille assembly, and replaced it with the new one. It was so easy, a caveman could do it!