JE2160SF03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Louis from Austin, TX
- Parts Used:
- WB36X10241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Post-Construction Cleaning People Used Brillo Pad on Microwave
My brand new never used microwave had the plexiglass all fogged up by no good cleaners using harsh abbrasives. The repair was quite simple but took a few minutes to figure out. You open the door and look at the end of the door. You can see the plexiglass screen edge. Slide a knife under the edge and work it up and down releasing the two face tape that holds it in place. Then using the knife to gently hold the plexiglass off of the tape simply slide it out the end. Put some two face tape on the new plexiglass in the same location, slide it in (bowing out the plexiglass while you slide the last little bit where the tape is) and once all the way in, press down to engage the tape. That is it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from EDINA, MN
- Parts Used:
- WB06X10500
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original feet, two disappeared. Uneven microwave.
Fast & easy. I was able to determine that this foot would work from the descriptions on online!! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from RALEIGH, NC
- Parts Used:
- WB49X10108
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I needed a new glass hot plate for a cracked plate that came with the original microwave.
I placed the new hot plate in the old microwave. It worked perfectly, and no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GAINESVILLE, TX
- Parts Used:
- WB27X10682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Everything Worked Fine But It Stopped Heating The Food.
Take the four saftey torx screws off the back of microwave that hold the side panels on. There are no screws in the front. Just pick up the side panels a little and slide towards the back of microwave and it will come off. The magnetron is visible behind control panel. Unplug the magetron, take a 3/8 nut driver , remove the one bolt that holds it on , remove and replace with the new one. Plug the wire (it will only go one way) back up and replace cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Portage, MI
- Parts Used:
- WB27X10907, WB27X10888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
was loud when cookiing
Went well, very easy to change once the microwave was out of the wall. Sounds better than when it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corey from Greenville, NC
- Parts Used:
- WB27X10682
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Micowave not heating food.
I just took off the cover, located the magnetron, replaced it and slapped everything back together and since then everything's been working pretty good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Skillman, NJ
- Parts Used:
- WB27X10907, WB27X10687, WB27X10688
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Not heat function
Went through diagnosis of the product, unit was not heating, fund the following items that were faulty, Wave unit was n/g, transformer ohm specs were n/g, also replaced main board due to poor LED visibility, changed out diode and capacitor due to age of the unit, unit working perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Hanover Park, IL
- Parts Used:
- WB24X10103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
tray would slowly rotate when door was open.
I determined that one of the 4 micro switches that interface with the door was faulty. Ordered that part and replaced it. Had to remove the cover and front control panel (without removing any connections. Two philips screws hold the limit switch assembly to the bracket. After removing those screws, twist the whole switch assembly clockwise around the mounting frame and now you can remove the defective micro switch and replace it with a new one. This works for any of the 4 switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Laurel, NY
- Parts Used:
- WB49X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass cooking tray broken
Simply replaaced broken cooking tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from New Orleans, LA
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems
Remove the Glass rotating tray and replace the guide
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Katy, TX
- Parts Used:
- WB36X10241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original barrier screen on the microwave bubbled and became warped after popping popcorn in microwave.
I slid the original barrier screen out of the door and slid the new one back in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Warner Robins, GA
- Parts Used:
- WB49X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass tray
just placed it on the wheel
Was this instruction helpful to you?
Thank you for voting!