JVM1660CH01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ina from Horn Lake, MS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor went out. Glass tray wouldn't rotate any longer
Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FISHERS, IN
- Parts Used:
- WB06X10420
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Turn table stopped rotating.
I tried to install the new part several times, but it didn't work. So I used a pencil to move things around down the shaft. After that the new part went in and now my microwave is doing what I need it to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Batavia, OH
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Light Socket
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CHESTERFIELD, VA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no lights on microwave
ordered 2 new sockets and bulbs easy replacement great service from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Fort Worth, TX
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from LINCOLN, CA
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Remove old light sockets and replace in Microwave over stove
Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- regina from weston, FL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotating plate broke
bought a replacement for it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Sedalia, MO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy cooking tray motor with electrical smoke smell
Just removed the screws from botton of unit, unplugged and removed the burned up motor, reveresed the process to install new motor. Less than 10 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Columbia, TN
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coupler broke at shaft & motor seized
Removed 5 philip head screws from under panel. Under panel droped down exposing drive motor. Removed one drive motor screw, replaced with new motor at the same time lining up new coupler. Pressed together, reinstalled motor srew, attached wire coupling and tested. Worked fine. Reinstalled lower panel screws (5)and unit was ready to go. I ordered two of each units because I believe this to be weak link in the unit. It was only 2 years old, used little as I have another home. I recently installed a like unit (Hanging) and it was a breez. 4 srews properly placed, electrical cord hole properly drilled & ready to go in 45 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Fredericksburg, VA
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Turntable Coupler was broken
I took the glass table up and underneath was the turntable coupler. I reached in with my hands and gently pulled the old coupler out. Once out I lined up the new one and gently pushed it in the hole until it locked into place. The process took about 5 minutes to complete. Very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jackson Center, OH
- Parts Used:
- WB36X10003, WB08X10016, WB01X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bulb and broken light socket
removed the bottom plate from microwave and replaced parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathie from Tipton, IN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turn table was making a terrible noise and wouldn't turn. I called a repair company and they told me it would be at least a hundred dollars to fix it.
I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from McDonough, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The microwave was making a lot of noise and the glass plate was turning very slowly.
I diagnosed the problem myself. I googled GE parts and was refered to you guys. I ordered the part and it took less than a 5 days to arrive. I used a phillips scewdrive to remove the cover of my microwave and removed the turning glass motor. This took less that 30min and cost less that $50.00. I figured that it would have cost me approx $125.00 to get a tech person to my home for this repair.
Thanks a lot!
Bernard
Thanks a lot!
Bernard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Orange, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable in microwave stopped working
I turned off the breaker/electric power to the microwave; opened the base of the microwave, detached the wire to the old drive motor, removed the
screws holding the drive motor in place; removed the old drive motor and installed
the new drive motor---beyond easy!!!
Thank you!
screws holding the drive motor in place; removed the old drive motor and installed
the new drive motor---beyond easy!!!
Thank you!
Was this instruction helpful to you?
Thank you for voting!