PVM1870SMC01 General Electric Microwave - Instructions

took glass cover off being an electrician and saw lamp or bulb was burned out. googled your site and with model number.went on partselect found lamp,orderd it.2 days later lamp arived installed lamp. So easy no running around or making several calls

It was just a matter of removing the old bulb and easily putting the new one in place. Very simple repair and the bulb was received amazingly fast. Was no doubt the best service I have received and I appreciate the quick response.

Screw out-old bulb out- new bulb in- screw back in!!!!!

Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.

The staff were terrific. Thanks so much as it had a happy ending.

Anita

unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-

as easy as it gets-

Repair was simple; only a phillips head screw driver was required to remove the access plate.

Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.

Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.

I used a phillips screwdiver to open the light cover protecting the halogen bulbs (2) both had burned out and needed to be replaced. A bit akward to replace, but within 5 minutes both were removed. I called your part service department to order replacements,(friendly and courteous service I might add!)was told that they would arive in about 3-5 days. 1.5 days later they were on my doorstep...They were promptly plugged into my GE underhood mounted microwave, now I am back in service! You've won me over and I will tell all my friends about you. Thanks again!

Removal of the bulbs was easy; reinserting was not as easy due to the configuration/placement of the bulbs in the unit. It was interesting that a simple suggestion to keep the bulbs covered with some of the packing material made sense as to not directly handling the bulb itself and causing any contamination of the bulb(s).

removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.

Simple install. Thanks for your prompt response to my order and interest.

the ones below were easy --underneath take out screws--take out old bulb--put in new one--the one inside a little more difficult--but not bad--take off panel on the front of microwave over door--the light is in a metal housing on the right--take out old bulb --put in new--wore rubber gloves putting in new lights--do not want to touch them with your fingers--i just watched the GE video on the parts website and it told me exactly what to do--if i can do it anybody can do it !

Uninstalled microwave from above range, removed cover then vent assembly (slide slightly to the left to free it). Opened the control panel (slide up then tilt forward) to access the troubleshooting/repair/test sheet. Followed the diagnostic flowchart and determined the TCO above the cooking cavity had failed. No other faults found. Ordered part Sat. afternoon and rcvd it Monday. Part is held in place with spring clips and quick connect terminals so installation was easy. Microwave was back in operation in no time.

Used new rubber gloves so as to not get finger prints on the bulbs. Hope that was ok. Trying to use a paper towel was a nuisance. Also had to use a mirror to see the slots for the bulbs. This was actually a pain to do especially since I am short and was on my toes to do this. Only the bright light works and before there was a night light and a bright light. So there you have it.

Disassembled the bottom of the microwave in order to access the lightbulb sockets. Unfortunately, 1 of the 2 replacement bulbs broke during the installation process - 1 of the pins broke off while trying to insert it. Now I have only 1 bulb so the light is not as bright as it should be. It took me several trips the HomeDepot only to have to return the bulbs. Fortunately, PartSelect shipped the correct replacement bulbs the first time.