JVM1650WBC05 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry from Schoolcraft, MI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turn table would not rotate
As in other postings, remove six screws on the bottom of the microwave, disconnected the the plug,unscrew two screws to remove the old motor...(it took longer to get the new part out its box then it did to make the repair) unpacked the new part, put in the two motor screws, put in the six screws to hold the microwave bottom in place and waalaa...done!
Thanks,
Hank
Thanks,
Hank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Vidalia, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable did not operate properly
took 6 screws out of the oven bottom
removed 2 screws that held the motor
diconnected the power plug.
plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven
That was it...
removed 2 screws that held the motor
diconnected the power plug.
plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven
That was it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Hampstead, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn table not turning
Removed the 5 screws that held the housing so it dropped down. removed the 2 screws to the motor. Disconnedted the plug. reinstalled the new motor. connected the plug and raised the housing and replaced the 5 screws. Took less than 10 minutes start to finish. Piece-of-cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from highland lakes, NJ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the tray started running slower to where it would not turn
about 6 philips head screws along the bottom drops that cover off. 2 more hold the motor in place.
carefully remove the 2 wire plug onto the motor . do not touch or get near the black wire.unless you want to get shocked.like i did.
remove the 2 motor screws.put the new one up and turn untill the screw holes are the holes in the
lower inner cover. reinstall the screws .reinstall the plug and lower plate.
having been a auto mechanic till i retired, helped me a lot.total time to make the repair was about 15 min.
this is not my first order from parts select and all i can say is they rock with the best of service i have ever gotten for appliance parts. and prices one can not found to beat for factory parts.
carefully remove the 2 wire plug onto the motor . do not touch or get near the black wire.unless you want to get shocked.like i did.
remove the 2 motor screws.put the new one up and turn untill the screw holes are the holes in the
lower inner cover. reinstall the screws .reinstall the plug and lower plate.
having been a auto mechanic till i retired, helped me a lot.total time to make the repair was about 15 min.
this is not my first order from parts select and all i can say is they rock with the best of service i have ever gotten for appliance parts. and prices one can not found to beat for factory parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Vista, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive tray table failed to turn
unplugged the appliance, removed the glass tray from inside, turned the microwave on its side and removed the 3x3 panel, removed the drive motor by taking out two screws and disconnecting the two electrical wires, compared the new item with the old one, placed new in olds position and screwed in place. replaced the 3x3 cover, turned microwave upright, plugged in the power cord, placed a cup of water on the tray, turned the microwave on for 30 sec. and watched the table turn. Very simple and convenient application.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Sparta, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the glass cooking tray would no longer move.
We removed the vents from under the bottom and then the 4 screws and pulled the motor out. It was a no brainer to fix and the part came in alot faster than expected.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Sneads Ferry, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the plate quit rotating inside oven
removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Villa Rica, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable wouldnt turn
easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!
I had previously read these steps others had posted on partselect so the job was a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from oak lawn, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
G.E. microwave turn table was loud and not working
I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from GRAND BAY, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Glass Cooking Table Not Turning - Food Burning
Most mirco wave have a plate on the bottom to protect turn table motor. This one had no screws - it has 6 tabs holding the protective cover. Used pliers to tear tabs. Used philip's driver to remove screw and turned motor to come out. Went back in reverse order replacing motor. Left protective plate off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olathe, KS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not turn
Removed five screws from the underside of the mircowave. Disconnected the two prong plug in. Removed the one screw that held the motor and replaced with new motor. Reconnected the plug and replaced the five screws
Tested the result with a bag of microwave popcorn. Worked perfectly.
Tested the result with a bag of microwave popcorn. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from MEXICO, NY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable would not rotate
Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from HOME, PA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Light in Microwave burnd out glas broken over lights
Replaced glass in frame and replaced lights
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Raleigh, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave Food Turntable Not Working
Reviewed the current postings surrounding the problem i was experiencing on your website. Located the 5 phillips head screws on the bottom panel. Removed them letting panel hinge down, removed the motor connector and checked for 21V AC with Volt Meter confirming the motor was not operable. Ordered replacement motor which arrived 3 days later during the holidays. Repeated the panel removal then removed the moter retaining screw and replaced with the received part a perfect matching. All in both panel removals for diagnostics and replacement of the motor took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!