JVM1650WBC05 General Electric Microwave - Instructions

I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

PS240270
Ceramic Fuse - 15 Amp
Easy installation , remove microwave cover housing ,locate fuse by door catch & replace..
Received quickly..
Replaced fuse , removed microwave cover housing , located fuse adjacent door catch removed & installed new fuse...

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

Removed the 1 inch plastic frame on inside of door, gave me access to 1 set of screws. The problem I encountered was, getting to the set that holds the handle to the door.I didn't realize the metal frame held the outside with flexible hooks, therefore once u snapped them off, the outside with the handle on it HIT the floor glass and all!
Fortunately it didn't break. Supporting the outside is most important.

Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

Replaced

Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.

Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.

First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.