SCA1000DWW03 General Electric Microwave - Instructions

Removed the door, removed the old choke cover (breaking all the stap catches), removed the slide door latch assembly from the spring (the most difficult task) then reassembly of the latch to spring, sliding into the grooves along the inside of the door, the installing the new choke cover (very easy with the new one) taking care not the break any of the staps. Easy enough! Another difficult task was to re-install the door to the frame. It appears that the lower "hinge" is slightly bent down to allow easy install but the door now makes a slight sweeking sound when opening and closing.

I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out

removed cover an replaced

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

On March 21st my wife's daughter and husband and I tackled the repair. I am physically limited, so their help was not only welcomed but necessary.First, removed two screws on the top of the oven to remove the vent panel. Then removed the door by lifting up (as described by others). Next removed the black plastic trim from around the window, using a table knife to pry it loose. Broke off some of the clips but that proved to be no problem at reinstallation. Removed 6 small screws holding the window assembly, but we were unable to pry the plastic tabs loose and we never were able to remove the panel. The screw to the upper end of the door handle is exposed and easily accessible. The screw holding the lower end of the handle is underneath the metal window assembly. We drilled a hole in the metal assembly until the screw was exposed. Removing the screw was a major undertaking. The housing in which the screw was imbeded would not release the screw. We used the drill with a small bit to drill the plastic out until the screw came free. It was difficult and tedious and time consuming. After finally releasing the two screws we began installation of the handle. We found the female receptacle on the handle was very reluctant to accept the screw, both top and bottom. The job was eventually completed after we lubricated the female receptacle adequately. Even so the handle is not quite a snug as I would have liked to have it.The job was hard, tedious, and took over two hours. reinstalltion of the door was no problem. I don't believe the designers and manufacturers intended amateurs to make this repair

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

This seems to be a fairly common occurrence so I've repaired this multiple times, once a year on average. The on site instructions are clear. Lift the top vent area off so you can remove the door. Open the door all of the way, lift off of the bottom peg and pull from the top. Lay door on a flat surface and with a small flat head screwdriver, gently pry the frame up (part 1804, door chock cover). There are small plastic tabs holding this part: use caution as they break easily. Once removed, on the door assembly, remove the small Philips screws: push the plastic tabs back, one side first; this part should then slide out. Both door handle screws are the exposed. Remove these (probably holding the broken handle parts, use the small screwdriver for lift to remove parts). Place the new handle on the door and replace the screws. replace the door assembly, be sure to lock all of the tabs back in place, snap door mask in place, replace door.

Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...

Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks

The primary door latch switch contacts were not closing properly. I broke the latch bracket while removing the switch. It is only a plastic clip that holds the switch in place. I replaced the switch and bracket. The Advantium now works in all modes.

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.

Removed. Inside frame with putty knife replace new latch attach spring and line up notch of latch in slots. That was the most difficult part replace inside frame. Done!

Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Removed tray from shipping container and installed in the microwave.