JVM2070WHC02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerry from New Milford, CT
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
interior/exterior bulb replacement
Inside "cavity" bulb was a PITA. Need to remove top decorative trim (2 screws and tabs) to access bulb housing. Broke 1 screw tab so be careful (Wiggle it more). Acccess to bulb housing was made for younger smaller hands, attached by 1 screw. Remove screw, rotate housing, replace bulb. Reverse proceedure. Outside bulb, cake...1 screw, drop lens replace bulb, your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Palm Desert, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
failed bulb
unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-
as easy as it gets-
as easy as it gets-
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from CUMMING, GA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had to replace to halogen lamps
Repair was simple; only a phillips head screw driver was required to remove the access plate.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Laguna Niguel, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface light bulbs burned out under microwave
Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Chantilly, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave interior lamp burned out
Unplug the microwave. Remove front grill and cover by removing 2 screws on top of microwave. You have to look down from the top. I could not locate the screws by feel. Once the two screws are out, remove the grill by sliding slightly to the left to lift out. Open the oven door to facilitate removal. Then remove the steel light cover (1 Phillips screw in the center of the unit) and unclip the bulb holder on the right. Do not touch the halogen bulb when you replace. Reseat the bulb holder and test by plugging in the unit with the door open. Unplug and replace the light cover and grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Dennis, MA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
overhead oven light in micro burned out, could not find correct halogen bulbs locally
took of the cover, replaced bulbs then replaced bulbs. One was more difficult to get in than the other but all is ok now. No more stove stop cooking in the dark:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Alpharetta, GA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
3 lights out--1 inside 2 below
the ones below were easy --underneath take out screws--take out old bulb--put in new one--the one inside a little more difficult--but not bad--take off panel on the front of microwave over door--the light is in a metal housing on the right--take out old bulb --put in new--wore rubber gloves putting in new lights--do not want to touch them with your fingers--i just watched the GE video on the parts website and it told me exactly what to do--if i can do it anybody can do it !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Stone Harbor, NJ
- Parts Used:
- WB25X10019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Burned out halogen bulbs
Used new rubber gloves so as to not get finger prints on the bulbs. Hope that was ok. Trying to use a paper towel was a nuisance. Also had to use a mirror to see the slots for the bulbs. This was actually a pain to do especially since I am short and was on my toes to do this. Only the bright light works and before there was a night light and a bright light. So there you have it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teri from Carmel, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced burned out lightbulbs
Disassembled the bottom of the microwave in order to access the lightbulb sockets. Unfortunately, 1 of the 2 replacement bulbs broke during the installation process - 1 of the pins broke off while trying to insert it. Now I have only 1 bulb so the light is not as bright as it should be. It took me several trips the HomeDepot only to have to return the bulbs. Fortunately, PartSelect shipped the correct replacement bulbs the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James K. from Humble, TX
- Parts Used:
- WB25X10019
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
How to remove microwave first?
The instructions for removing and installing the new bulbs appear to be great; however, nothing tells me how to remove the microwave from the mounting so I can then invert it and take care of the bulb issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Kennett Square, PA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bilbao burned out
Simple repair..took off covering with screwdriver removed the halogen bulb and replaced with the one I ordererd..wish all repairs went so well..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Laguna Niguel, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
both bulbs burned out
I used a phillips screwdiver to open the light cover protecting the halogen bulbs (2) both had burned out and needed to be replaced. A bit akward to replace, but within 5 minutes both were removed. I called your part service department to order replacements,(friendly and courteous service I might add!)was told that they would arive in about 3-5 days. 1.5 days later they were on my doorstep...They were promptly plugged into my GE underhood mounted microwave, now I am back in service! You've won me over and I will tell all my friends about you. Thanks again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from El Cerrito,, CA
- Parts Used:
- WB25X10019, WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light lens was cracked
Had to remove one screw from the light lens metal frame. Then slid the broken glass out and replaced. Pulled out the two prong bulb and put the new one straight in. Put back frame and screw. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Boynton Beach, FL
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulbs
One screw out - drop panel - remove and replace bulbs!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Berea, OH
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both Nite lights burned out, again.
So simple, unscrew the hatch underneath the microwave oven, pull out old bulbs, and insert new.
Was this instruction helpful to you?
Thank you for voting!