JVM1340WWC01 General Electric Microwave - Instructions

First I removed the inner snap seal to expose the lower screw to the handle. Once the handle was removed the outer frame came off. I then installed the new frame and the handle and replaced the inner snap seal. Nothing to it.

Followed the online videos to enter the cavity to the switch holder. Noticed right away the dreaded capacitor was in back right corner behind where the touch pad had been removed. I isolated the capacitor with an old computer mouse pad for extra safety. Took some manipulations to get the switch mount out from behind the wire bundles. Once out front, easy to use small flat blade screwdriver to release each switch and replace with matching new switch. Only one switch was bad but replaced all three. Back together and working great.

Removed the outer cover to access the door switches. Turns out there were three switches, but I determined that only two were bad. When the small colored tab on the switch is pushed in it should make a clicking sound. The two bad switches had no resistance and did not make any noise when pressed. Removing the switch is relatively easy, you simply pull it away from a couple small tabs holding them in place. After reconnecting the wire leads, insert back into the holding tabs and install the cover.

I used the internet and your directions to complete the repair. It was easy!

Imagine the surprise on my daughter's face when she went to open the microwave and the handle broke in half! I called multiple places locally, and ten days was the soonest I could find the part. I went online and ordered from PartSelect....three days later we were back in business. Good job, guys! And I installed it myself! A single mom from Texas

removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.

removed visble screw. Then lifted the inside door rim around the glass to reveal the hidden screw. Removed that screw and replaced broken handle with new handle and screwed it in place. Replace part of rim that was lifted to reveal the hidden screw.

Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube

Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.

Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

The old one was extremely difficult to remove, like it was ‘welded‘ in place. I had to crush and destroy it with vice grips in order to get it. it off. The new one would not go on unless I modified it by removing a “spur“ which prevented it from sitting flush with the bottom of the oven. All in all it took less than 25 minutes and it is now working well.

My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

.Thank You Dan