JVM1870WFC01 General Electric Microwave - Instructions

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.

This repair can be don in under 5 minutes, easily !!

The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.

1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!

Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.

ha to remove the bottom ,to get at the internal screws that held the drive motor. after disconnecting the power to the moter, i removed the two screws that held it in place. i installed thre new motor , reconnected the wire plug to motor . replaced the outer screws, and the project was done.

Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!

Removed 5 screws to allow lower pan to hang down. Unplug motor, remove 2 more screws that hold motor in and pull it out. and reverse process for reinstallation of new motor. Took all of 4 minutes allowing time to drink a beer while taking the new motor out of the box

First I removed the 6 screws that hold the bottom panel in place. I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then connected the two wires to the new element. Secured the element in place and replaced bottom panel.

Real simple process!
Thanks!

This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!

removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel

I removed the five screws that held the bottom plate in place. After removing the bottom plate, I unscrewed the one screw holding the drive motor, unplugged the motor, and then installed the new motor. Replaced the botton plate and then tested the new motor. Everything worked like new.

The part was less expensive than buying it from GE. I ordered the motor on a Monday morning and received it Wednesday afternoon. I was completely satisified with the price, part, and shipping time.

Thanks,

Removed six screws that allowed the "bottom" to swing down; then removed the two screws holding the motor - disconnected the two wires. Installed the motor and reversed this procedure to finish the project.

Let me keep this short and simple.

Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order

Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.

about 6 philips head screws along the bottom drops that cover off. 2 more hold the motor in place.

carefully remove the 2 wire plug onto the motor . do not touch or get near the black wire.unless you want to get shocked.like i did.

remove the 2 motor screws.put the new one up and turn untill the screw holes are the holes in the
lower inner cover. reinstall the screws .reinstall the plug and lower plate.

having been a auto mechanic till i retired, helped me a lot.total time to make the repair was about 15 min.

this is not my first order from parts select and all i can say is they rock with the best of service i have ever gotten for appliance parts. and prices one can not found to beat for factory parts.