JVM1190SYC01 General Electric Microwave - Instructions

changed the bulb

With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

so easy, but how do i turn light off?

Part recieved next day. thanks so much

removed the lens cover with one screw and replaced bulb

I use a chopstick to help get the belt under a piece of metal between the fan and the wheel that turn the belt. I thought I might have to get a new oven, but the belt replacement seems to have fixed the problem.

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

removed cover and replaced belt. very simple! Many thanks for your prompt service.

undid plate exposing bulbs. Bulbs were blown to the extent that I could not see the size or wattage. Went to website, got the data ... including how to find the model and serial number plate, entered the info, looked at the exploded drawing, ordered 2 new bulbs and 3 days later they showed up at our door FedEX.

Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.

removed access panal, found soft switch as discribed on your web site. removed and replaced.

thank you very much.

Unscrewed the grill, removed old filter. Inserted new filter. replaced the grill, screwed it in. The end. Oh washed the grill before replacing.

Removed the microwave with the buit in housing from the cabinet. Removed microwave from built in housing. Removed outer cabinet giving access to remove control panel and smart board where switches are located. Removed control panel to get to smartboard. Removed smart board after disconnecting a few wires to allow easy removal. Individually removed and then tested each switch using multimeter. Found seondary Door Switch (bottom of smart board) operation to be intermittent (switch trip button extremely loose and rattle inside this particular switch) Ordered replacement part which came very quickly on standard shipping order. Put new switch on smart board and remounted, reinstalled control panel and reconnected various wire connectors previously disconnected. Then plugged in oven and tested for opertation - didn't work at all! But, after bleeding off capacior charge by removing connectors and discharging capacitor to ground, then reassembling control board and smart board into oven, then trying agian, it has worked perfectly ever since. Do not understand why capacitor disconnect/discharge was required but suspect this reset the control electronics. Easy fix and hope to get another 12 years out of this appliance which is used multiple times every day. Also have two other identical micorwave ovens, one is 20 years old, but these get used relatively infrequently.

Took out 3 screws total, cleaned accumulated grease off of inside parts, put bulb and filter in, closed up by re-installing 3 screws.

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.