JVM1860CDC01 General Electric Microwave - Instructions

Followed the easy directions that came with the replacement filter

Took out the screw holding the old motor, unpluged it and reversed the procedure to install new part. My wife is now very happy!

Removed filter, removed five (5) screws, lowered lower pan, disconected feed wire, removed screw holding the moter, twisted old moter out. Twisted new moter in, replased screw, conected feed wire, closed pan, replased five (5) screws, replaced filter. Tested microwave with glass of water in it.

All went well.

From part order to finish was less then five (5) days.

The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.

Removed the five screws that allowed the bottom panel of the microwave to drop down at an angle, still attached at the rear. Took the old motor out by removing the two screws holding it and replaced it with the new motor. Reversed to process to install the new motor. Had to take off the plastic piece inside the microwave that holds the glass plate that turns and then replace it after I got the new motor installed.

First I unpluged the power cord. Then I removed five screws on the bottom panel which will swing down to reveal the turntable motor. I removed the electrical plug from the motor and the two screws that hold the motor in place. Put the new motor in place and align the flat side of the motor shaft with the hole in the bottom of the turntable. Fasten the two screws that hold the motor back in place and reconnect the power plug to the motor. Swing the bottom panel back in place and secure with the five screws. Plug the power cord back in and reset the clock and you are ready to use the microwave.

This was a very simple do-it-yourself repair and information on the partselect website was very helpful. The order and shipping process was simple and fast. Anyone who knows which end of a screwdriver to use should be able to do this repair.

The ground shipping took less than three days. When I got home from work the part was at home. While I was having dinner I told my 17 year son to get a phillip screw driver. He unplugged the power from the wall. He removed five screw from the bottom of microwave. He then removed one screw from the drive motor, disconnected motor plug, reconnected the plug to the new motor, placed back one screw on the motor and screwed back the five screws. Tested the microwave and the tray was turning successfully. It took my son less than five minutes. Real easy and highly recommended.

Part arrived sooner than expected---great service!!!!Simply drop down the light/grill panel under the unit--it's hinged in the rear. Unplug and unscrew the motor --replace in reverse order. Done PS -Local GE sales and repair could not get this motor. Said GE no longer provided , too old---6 years

I removed the 7 screws on the cover for it to drop down. Then disconnected the 2 plugs from the motor and removed 2 screws that was holding the motor in place. Connected the new motor to the plugs, screwed back in place, and then screwed the cover up. Total time: approximately 15 minutes. I suggest you put a towel on top of the stove for protection. Easy to do. Thank you.

remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.

Removed the bottom of microwave , removed the tray motor and replaced with new motor. total time 10 min.
Simple

Only needed a phillips screwdriver to remove screws from the bottom of the microwave. Unplugged the motor, removed the two screws holding it in place, put the new motor in place replaced the screws, and replaced the bottom. It took about 10 min.

Removed 5 screw to lower filter plate under microwave (under counter). Unplugged drive motor. Removed plate and drive adapter from inside oven by pulling adapter straight up. Removed one screw holding drive motor and then rotate motor to relrase motor ftom clip. Replaced motor in the reverse order as above.

Motor came in on time and worked perfect.

Removed bottom cover 6/7 phillips screws, pulled plug out of motor , removed two holding screws,replaced motor and reversed the procedure.

I removed the five screws that hold the cover plate on the bottom of the microwave flollowed by removing the electrical connection. Then I removed one screw to remove the motor. Replaced with new motor and screwed into place. Final was to connected electric and then returned the plate and fastened with the five screws.