Models > JVM1870SFC02 > Instructions

JVM1870SFC02 General Electric Microwave - Instructions

Jump to:

All Instructions for the JVM1870SFC02
121 - 135 of 336
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Lanier from Adairsville, GA
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
tray turned slow or stopped
Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from Youngsville, NC
Parts Used:
WB26X10038
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Noisy Glass Cooking tray
The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.

1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dik from QUINCY, MA
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Stirrer Motor stopped working
Using a phillips screwdriver, remove 7 screws from the unerpanel of the Spacesaver Microwave. The panel will swing down from the rear edge hinge, exposing the lights and the stirrer motor. Remove the electrical connector and two screws holding the motor in place and remove the motor. The stirrer inside the oven can then be removed if desired. Install the new motor in reverse order. Note rotate the stirrer inside the oven to align the motor shaft to facilitate assembly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
johnny from port orange, FL
Parts Used:
WB24X10047
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
no power in microwave in turn table wouldn't turn light would work act like door was open
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
5 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from BLUFFTON, SC
Parts Used:
WB24X10047
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
The unit would run when the door was open!
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from FULSHEAR, TX
Parts Used:
WB24X10047
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
M/W would not start. control panel OK
unplugged power
removed main black cover.
located part WB24X10047 and replaced
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas R. from ETOWAH, NC
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Microwave turntable barely moving and motor making loud noises
Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from MEXICO, NY
Parts Used:
WB26X10038
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Turntable would not rotate
Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from Wesley Chapel, FL
Parts Used:
WB24X10047
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sheldon from Boca Raton, FL
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Water over flow killed Tray Drice Moter
Removed filter, removed five (5) screws, lowered lower pan, disconected feed wire, removed screw holding the moter, twisted old moter out. Twisted new moter in, replased screw, conected feed wire, closed pan, replased five (5) screws, replaced filter. Tested microwave with glass of water in it.

All went well.

From part order to finish was less then five (5) days.

The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Marana, AZ
Parts Used:
WB36X10071
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Loudon, TN
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The motor that turned the glass tray made a loud noise.
Removed the five screws that allowed the bottom panel of the microwave to drop down at an angle, still attached at the rear. Took the old motor out by removing the two screws holding it and replaced it with the new motor. Reversed to process to install the new motor. Had to take off the plastic piece inside the microwave that holds the glass plate that turns and then replace it after I got the new motor installed.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from Greensboro, NC
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Turntable stopped working
First I unpluged the power cord. Then I removed five screws on the bottom panel which will swing down to reveal the turntable motor. I removed the electrical plug from the motor and the two screws that hold the motor in place. Put the new motor in place and align the flat side of the motor shaft with the hole in the bottom of the turntable. Fasten the two screws that hold the motor back in place and reconnect the power plug to the motor. Swing the bottom panel back in place and secure with the five screws. Plug the power cord back in and reset the clock and you are ready to use the microwave.

This was a very simple do-it-yourself repair and information on the partselect website was very helpful. The order and shipping process was simple and fast. Anyone who knows which end of a screwdriver to use should be able to do this repair.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kent from Puyallup, WA
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The drive motor was making a loud, horrible noise.
Simple as could be: unplug the microwave, remove 5 phillips screws to access the motor, remove the 2 phillips screws holding the motor in place, un-clip the motor from it's power supply, and reverse the process; you're done! It took all of 3 minutes to complete.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Lake Sherwood, MO
Parts Used:
WB26X10038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The turntable began operating intermittently and making noise
The repair was extremely easy. Remove seven screws in the bottom trim, slip the electrical connector off and remove the two screws holding the motor. Slide the new motor into position, replace the connector and screws.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM1870SFC02
121 - 135 of 336