JVM1740WMC01 General Electric Microwave - Instructions

It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!

placed plate on carousel

I replace the grill with a new one.

I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair

Removed the bottom panel from the microwave. Check to see if there was still power going to the turntable motor. There was still power there. Looked up the microwave model# on the website which showed a full display of the microwave parts. Selected the part. When the part arrived. Removed the bottom panel off the microwave. Removed the 2 screws holding the turntable motor in place. The new turntable motor was slightly different so I did have to cut a small slot in the new turntable motor so it would slide into the punched out slot so it would sit in the correct position. The job was still very easy and I complete the repair in about 20 mins. It was great to be able to do the repair myself and saved me some dollars. I would definitely recommend PartsSelect.com to anyone.

Easy. A little awkward getting to the part since microwave is over stove and not much room between range and microwave. Other than that, it was a piece of cake.

I replaced the cover just fine but i think a sensor went bad

Very easy replacement. Just lift out and replace with a new one!

My son had to replace the bulbs because the screw that holds the bulb shield was so tight that I couldn't remove it. It was too difficult for me to do it myself.

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

Because the microwave is old and the bulbs, I believe, had never been changed I carefully tried to unscrew the bulb. However, when I went to unscrew the bulbs the end of the bulb broke off and remained in the socket. I used a few different tools then remembered that sometimes a raw potatoe can be used to unscrew the remainder of the bulb, but to no avail. Finally had to unscrew the whole underside of the microwave to remove the broken bulb. May I suggest that you have the socket face away from the wall to screw in the bulb instead of the socket pointing toward the wall. You need to know yoga just to manuver the bulb into the socket.

Removed 5 screws from the bottom of the over the range microwave to expose the light sockets. Removed the 1 screw holding the socket, disconnected the wires. Attached the wires to the new socket, Put in the bulb, reattached it with the screw. Repeated on the other light... It took about 20 minutes and now the lights work just like they should :)

The order was easy and promptly received. I lowered the cover by removing retainer screws underneath. Simply lowered it and removed the broken glass and replaced it. The bulb was broken and the base of it was stuck in the socket. I didn't bother to remove it because the socket was brittle. I disconnected the socket by unplugging the wires, removing the retainer screws,and removing it. I replaced it with the new one. Screwed in the bulb. I replaced the cover and it was done. Ps: I used an Hitachi cordless screwdriver, which greatly helped when doing this alone.

Unplugged microwave before doing anything.Removed 6 screws holding the bottom of the microwave on. Disconnected 1 wire connector connecting the light sockets.Removed 1 screw on each socket to remove and install new socket. Reconnect the 1 wire connector and reinstall the 6 screws holding the bottom of the microwave on. Removed 1 screw holding the glass lens in place on each light and installed 1 bulb in each and reinstall 1 screw in each lens. Replug power cord. DONE !!