JVM1429CDC02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from Sneads Ferry, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the plate quit rotating inside oven
removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Villa Rica, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable wouldnt turn
easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!
I had previously read these steps others had posted on partselect so the job was a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Sparta, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the glass cooking tray would no longer move.
We removed the vents from under the bottom and then the 4 screws and pulled the motor out. It was a no brainer to fix and the part came in alot faster than expected.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cory from Galesburg, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable / cooking tray not rotating
Let me keep this short and simple.
Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order
Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Vista, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive tray table failed to turn
unplugged the appliance, removed the glass tray from inside, turned the microwave on its side and removed the 3x3 panel, removed the drive motor by taking out two screws and disconnecting the two electrical wires, compared the new item with the old one, placed new in olds position and screwed in place. replaced the 3x3 cover, turned microwave upright, plugged in the power cord, placed a cup of water on the tray, turned the microwave on for 30 sec. and watched the table turn. Very simple and convenient application.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Puyallup, WA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drive motor was making a loud, horrible noise.
Simple as could be: unplug the microwave, remove 5 phillips screws to access the motor, remove the 2 phillips screws holding the motor in place, un-clip the motor from it's power supply, and reverse the process; you're done! It took all of 3 minutes to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Plymouth, MI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy cooking tray while spinning
7 screws, lowered the bottom and replaced the motor with two more screws. It was fairly easy and I'm pretty proud of myself.
The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.
The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Justice, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out -cracked holder lamp
pluged wires back on ,placed lamp holder and bulb back and replaced screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Zieglerville, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced drive motor on GE Spacemaker microwave
I thought this would be a major project but tured out to be very simple - 7 screws, 10 minutes and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lake Sherwood, MO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turntable began operating intermittently and making noise
The repair was extremely easy. Remove seven screws in the bottom trim, slip the electrical connector off and remove the two screws holding the motor. Slide the new motor into position, replace the connector and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Colorado Springs, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor quit working
As others have desribed - remove 5 screws from the bottom cover. Lower cover and replace turntable motor with 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Bradenton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor burned out
Told by appliance repair service that parts were very expensive and service call started at $80 minimum. Finding replacement motor on your site was very easy. Instructions on repair were very complete and included pictures of the motor itself which had same capacity as replacement motor. Before ordering part from PartSelect I followed the online instruction for repair/replacement of the Microwave table motor and it was exactly as described. Removed filters and 10 screws with a single Phillips head screw driver. Motor looked the same as picture and ordered it. Part arrived in 24 hours and it took 4 minutes to replace the motor from start to finish. Total costs including shipping was approx 40 dollars. Great service and great site. This is my second repair using PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from New York, NY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turnatable stopped rotating; GE said to buy a new micowave, that it would cost just as much to fix.
The delivery was lightening fast...which I didn't expect. Great service.
First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.
It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.
And to think GE said to buy a new one!
First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.
It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.
And to think GE said to buy a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zayne from Blanchard, OK
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cooking Tray stopped turning, motor rattled
Removed the screws holding the bottom cover on, removed screws holding motor in place, replaced motor, put everything back in. Simple as changing batteries.
The nice thing is that PartSelect, as always, delivered exactly what I needed and very fast. Ordered on a Wednesday and received it on Thursday (the very next day!)
The nice thing is that PartSelect, as always, delivered exactly what I needed and very fast. Ordered on a Wednesday and received it on Thursday (the very next day!)
Was this instruction helpful to you?
Thank you for voting!