JVM1540WMC02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ricardo from Port St Lucie, FL
- Parts Used:
- WB56X10723
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke door glass like the clumsy fool that I am
Decided best way to repair was replace the whole door. Yes it was a pricy repair, however I did not want the landlord to find out. I placed the old door with shattered glass pieces taped up in the box and disposed of properly and no mess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from gulfport, MS
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass broken
replaced the glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Lathrop, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drop and shattered the glass tray
It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from CHEHALIS, WA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no lights
Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Puyallup, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass tray broke in microwave
Removed tray from shipping container and installed in the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from San Marcos, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken micro tray
placed plate on carousel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SUGAR HILL, GA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burn ed out bulbs
I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ISAAC from MADAWASKA, ME
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Tray
Very easy replacement. Just lift out and replace with a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Alexandria, VA
- Parts Used:
- WB06X10468
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hoplders was melted by steam fron burner on stove
self
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Pittsburgh, PA
- Parts Used:
- WB36X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
over range top light bulbs burned out
My son had to replace the bulbs because the screw that holds the bulb shield was so tight that I couldn't remove it. It was too difficult for me to do it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Anaheim, CA
- Parts Used:
- WB06X10130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave will not come on
I replaced the cover just fine but i think a sensor went bad
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Boone, NC
- Parts Used:
- WB26X10208
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Turntable stopped turning
Removed the bottom panel from the microwave. Check to see if there was still power going to the turntable motor. There was still power there. Looked up the microwave model# on the website which showed a full display of the microwave parts. Selected the part. When the part arrived. Removed the bottom panel off the microwave. Removed the 2 screws holding the turntable motor in place. The new turntable motor was slightly different so I did have to cut a small slot in the new turntable motor so it would slide into the punched out slot so it would sit in the correct position. The job was still very easy and I complete the repair in about 20 mins. It was great to be able to do the repair myself and saved me some dollars. I would definitely recommend PartsSelect.com to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from N Chesterfield, VA
- Parts Used:
- WB26X10208
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not working
Easy. A little awkward getting to the part since microwave is over stove and not much room between range and microwave. Other than that, it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Myrtle Beach, SC
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven light bulb burned out
After discovering Parts Select website and reading the experiences and installation instructions of others with similar experiences, it gave me the confidence to give it a try. I order the parts, and in a few days, they arrived. I did the following, as read from others: 1. unscrewed the 5 screws on bottom panel of microwave. 2. Had wife hold panel while I unscrewed the 1 screw holding the lamp socket 3. Pulled lamp socket out of hole 4. Used needle nose pliers to pull wiring from old lamp socket 5. plugged the two wires into new lamp socket 6. removed old bulbs (which would have been a nightmare to do by just dropping down the bulb cover - bulb had been factored glued to lamp socket and even after I removed the glue, the bulb still broke when trying to remove the bulb - had to use needle nose pliers to unscrew the base of the broken bulb) 7. placed lamp socket with new bulb back into its slot and screwed the one screw holding the lamp socket back 8. screwed back in the 5 screws that held the bottom panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emanuel from Woodstock, VA
- Parts Used:
- WB06X10436
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Converted an over the range microwave from non vented ductless to outside vent.
Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.
Was this instruction helpful to you?
Thank you for voting!