JVM6175WVC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- edward from schererville, IN
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad bulb
unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerri from north haven, CT
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bulb /microwave
simply to install new bulb. Unscrewed the under the microwave lamp door with a screwdriver. Inserted new bulb into socket. good to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from ALEXANDRIA, VA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace micro/hood combo stove light
simply unscrewed protective lens cover, and swapped bulbs--these bulbs are great--last for years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SUGAR HILL, GA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burn ed out bulbs
I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Camp Hill, PA
- Parts Used:
- WB06X10596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter not cleaned for 7 years !
Threw the old filter away and slide the new one in without any tools ! Filter should be cleaned every month - who knew ?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Springfield, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Insulator around light socket Broke.
Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Arlington, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb in the over-stove microwave
Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Zebulon, NC
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb separated from base, leaving base in socket. Unable to remove base without damaging socket.
Removed 5 phillip screws from bottom plate of microwave oven to lower the plate and gain access to the socket. Then, removed screw(s) attaching socket to the oven. Installed socket, and secured the bottom plate of the oven with screws removed previously.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Alvaton, KY
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out and socket broken
Fist I removed the 5 screws under the microwave. Then I dropped the panel and accessed the socket. I removed the socket by removing the one screw and disconnecting the wires. Replaced the wires on the new socket, installed the new bulb and reattached with the screw. replaced the panel with the 5 screws and I was done. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Katy, TX
- Parts Used:
- WB06X10596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter frame weld at corner opened.
Simple install. Thanks for your prompt response to my order and interest.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Walpole, MA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Bulb Light Replacement
I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from st augustine, FL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the light over the stove top went out
I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from STRONGSVILLE, OH
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out microwave light bulb and base broke off in light socket
Replaced light socket and bulb. Real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS from SPRING, TX
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light bulb fused it self to socket
replace socket
Was this instruction helpful to you?
Thank you for voting!