JVM6175BVC01 General Electric Microwave - Instructions

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.

Unplugged microwave before doing anything.Removed 6 screws holding the bottom of the microwave on. Disconnected 1 wire connector connecting the light sockets.Removed 1 screw on each socket to remove and install new socket. Reconnect the 1 wire connector and reinstall the 6 screws holding the bottom of the microwave on. Removed 1 screw holding the glass lens in place on each light and installed 1 bulb in each and reinstall 1 screw in each lens. Replug power cord. DONE !!

After discovering Parts Select website and reading the experiences and installation instructions of others with similar experiences, it gave me the confidence to give it a try. I order the parts, and in a few days, they arrived. I did the following, as read from others: 1. unscrewed the 5 screws on bottom panel of microwave. 2. Had wife hold panel while I unscrewed the 1 screw holding the lamp socket 3. Pulled lamp socket out of hole 4. Used needle nose pliers to pull wiring from old lamp socket 5. plugged the two wires into new lamp socket 6. removed old bulbs (which would have been a nightmare to do by just dropping down the bulb cover - bulb had been factored glued to lamp socket and even after I removed the glue, the bulb still broke when trying to remove the bulb - had to use needle nose pliers to unscrew the base of the broken bulb) 7. placed lamp socket with new bulb back into its slot and screwed the one screw holding the lamp socket back 8. screwed back in the 5 screws that held the bottom panel.

Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.

As suggested, I placed a towel over the stove. Only had 3 main screws to remove from bottom of microwave. Dropped the bottom and changed the sockets and light bulbs. After replacing the bottom tray, I put the new glass light lens in. The clips on glass holder bent back like a photo frame-really easy. Turned on the lights and was done.

Removed 5 phillip screws from bottom plate of microwave oven to lower the plate and gain access to the socket. Then, removed screw(s) attaching socket to the oven. Installed socket, and secured the bottom plate of the oven with screws removed previously.

Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.

Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.

lower hood; support hood with spice rack;angle just right; unscrew light socket; remove wiring harness; replace; connect wiring harness;

undid plate exposing bulbs. Bulbs were blown to the extent that I could not see the size or wattage. Went to website, got the data ... including how to find the model and serial number plate, entered the info, looked at the exploded drawing, ordered 2 new bulbs and 3 days later they showed up at our door FedEX.

Simply unscrew the bottom panel of the microwave device (it swings downward when opening - there are hinges on the back to protect it from falling down). Remove the old light socket (which is modular and is screwed in place)from the connectors and then replace it with the new light socket. That's it

Using a #2 Phillips screwdriver and removed the screw that retains the lens frame around the broken lens. I also did the same to the opposite side (whose lens was fine but the bulb had been burned out for some time). With my fingers I pryed up the frame clips that secure the lens in place, removed the pieces of the broken lens, and replace the lens with one of the new lenses I had ordered. Although the bulb on this side was still burning, I replaced it with one of the two I ordered anyway. When I removed the bulb that was burned out, the glass separated from the bulb's base. However, I simply put on a set of tight fitting leather gloves and used my ring finger to apply pressure inside the base and it soon began to twist and then came out. This takes a little manual dexterity, but is very doable. If it were too tight, you could take a large "easy-out" tool (like the one to fit a 3/8" - 1/2" hole) and it would remove the broken base in short order. I had also ordered a second lens, but the lens on the burned side was simply dirty, so I cleaned it, put it back in place and saved the new one for a rainy day. By the way, BE ABSOLUTELY CERTAIN THE LIGHTS ARE SWITCHED TO THE "OFF" POSITION BEFORE DOING ANY OF THE ABOVE. Also take care to clean the glass on the bulbs with denatured alcohol and handle them with clean cloth gloves or a tissue so as not to allow any oils to be on the surface when they are switched on. Body oil will immediately create a hot spot which will shorten the life of the bulb by at least 50% if not more.

replace socket