JVM1660BBC02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Marina Del Rey, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb wouldn't light.
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CELIA from TINLEY PARK, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass Tray Quit Spinning
First I removed the 6 screws that hold the bottom of the microwave . I was able to see and get to the cooking tray drive motor. I removed the 2 screws and took out the motor. I replaced the motor and replaced all the screws. Started the microwave and it worked , no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Plymouth, MI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy cooking tray while spinning
7 screws, lowered the bottom and replaced the motor with two more screws. It was fairly easy and I'm pretty proud of myself.
The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.
The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Cary, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
motor that rotates glass cooking tray was not working
Disconnect the power cord. Removed the screws locate under the spacesaver microwave. The bottom will swing down and hang off the hooks on the back edge. Disconnect the wires plugged into the broken motor. Remove the two screws that hold the broken motor in place. Replace with new motor and re-insert screws and motor wires. Reassemble bottom panel and plug power cord back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Bradenton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor burned out
Told by appliance repair service that parts were very expensive and service call started at $80 minimum. Finding replacement motor on your site was very easy. Instructions on repair were very complete and included pictures of the motor itself which had same capacity as replacement motor. Before ordering part from PartSelect I followed the online instruction for repair/replacement of the Microwave table motor and it was exactly as described. Removed filters and 10 screws with a single Phillips head screw driver. Motor looked the same as picture and ordered it. Part arrived in 24 hours and it took 4 minutes to replace the motor from start to finish. Total costs including shipping was approx 40 dollars. Great service and great site. This is my second repair using PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Canal Winchester, OH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Micro Glass Tra Y Quit Rotating.
Took out the screw holding the old motor, unpluged it and reversed the procedure to install new part. My wife is now very happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Manassas, VA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grinding noise, tray didn't always turn.
Repair was simple. Remove screws on bottom panel of microwave, let cover hang on hinges. Remove two screws from drive motor, remove old motor, insert new motor, replace two screws, then reattach bottom panel. Done!
Quiet has returned to my microwave:-)
I also discovered that the (night light) bulbs are much easier to replace when the bottom panel is lowered.
Quiet has returned to my microwave:-)
I also discovered that the (night light) bulbs are much easier to replace when the bottom panel is lowered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from New York, NY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turnatable stopped rotating; GE said to buy a new micowave, that it would cost just as much to fix.
The delivery was lightening fast...which I didn't expect. Great service.
First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.
It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.
And to think GE said to buy a new one!
First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.
It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.
And to think GE said to buy a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Spartanburg, SC
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass turntable broke when being washed.
Ordered the part on Monday, it was delivered on Wednesday, only paid for standard shipping. All I had to do was put it in, right part, back to new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Puyallup, WA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drive motor was making a loud, horrible noise.
Simple as could be: unplug the microwave, remove 5 phillips screws to access the motor, remove the 2 phillips screws holding the motor in place, un-clip the motor from it's power supply, and reverse the process; you're done! It took all of 3 minutes to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheldon from Boca Raton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water over flow killed Tray Drice Moter
Removed filter, removed five (5) screws, lowered lower pan, disconected feed wire, removed screw holding the moter, twisted old moter out. Twisted new moter in, replased screw, conected feed wire, closed pan, replased five (5) screws, replaced filter. Tested microwave with glass of water in it.
All went well.
From part order to finish was less then five (5) days.
The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.
All went well.
From part order to finish was less then five (5) days.
The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Marana, AZ
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Loudon, TN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The motor that turned the glass tray made a loud noise.
Removed the five screws that allowed the bottom panel of the microwave to drop down at an angle, still attached at the rear. Took the old motor out by removing the two screws holding it and replaced it with the new motor. Reversed to process to install the new motor. Had to take off the plastic piece inside the microwave that holds the glass plate that turns and then replace it after I got the new motor installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Greensboro, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable stopped working
First I unpluged the power cord. Then I removed five screws on the bottom panel which will swing down to reveal the turntable motor. I removed the electrical plug from the motor and the two screws that hold the motor in place. Put the new motor in place and align the flat side of the motor shaft with the hole in the bottom of the turntable. Fasten the two screws that hold the motor back in place and reconnect the power plug to the motor. Swing the bottom panel back in place and secure with the five screws. Plug the power cord back in and reset the clock and you are ready to use the microwave.
This was a very simple do-it-yourself repair and information on the partselect website was very helpful. The order and shipping process was simple and fast. Anyone who knows which end of a screwdriver to use should be able to do this repair.
This was a very simple do-it-yourself repair and information on the partselect website was very helpful. The order and shipping process was simple and fast. Anyone who knows which end of a screwdriver to use should be able to do this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from HOME, PA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Light in Microwave burnd out glas broken over lights
Replaced glass in frame and replaced lights
Was this instruction helpful to you?
Thank you for voting!