JVM1540SMC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from N Chesterfield, VA
- Parts Used:
- WB26X10208
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not working
Easy. A little awkward getting to the part since microwave is over stove and not much room between range and microwave. Other than that, it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bluffton, SC
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out lightbulbs.
Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Buford, GA
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light socket crumbling apart
Unplugged microwave before doing anything.Removed 6 screws holding the bottom of the microwave on. Disconnected 1 wire connector connecting the light sockets.Removed 1 screw on each socket to remove and install new socket. Reconnect the 1 wire connector and reinstall the 6 screws holding the bottom of the microwave on. Removed 1 screw holding the glass lens in place on each light and installed 1 bulb in each and reinstall 1 screw in each lens. Replug power cord. DONE !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Santa Maria, CA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bulbs blew and disintegrated when removal was attempted
Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Pasco, WA
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace stovetop light socket
Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from schererville, IN
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad bulb
unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.
Was this instruction helpful to you?
Thank you for voting!