All Installation Instructions for General Electric Microwave JVM1540BMC01

Customer:: Judy Ann from Fort Pierce, FL
Parts Used:: WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bulb was burnt out

Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Andrew from Bolton, CT
Parts Used:: WB36X10071, WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Light bulb was burnt out and lens was broken

Unscrewed the lens, it hinged down, then I could remove the frame. Pulled old bulb out and replaced with new one. Replaced broken glass in frame. Reset hinge into the holes and swung it up into place. Screwed it in.

Very easy!

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Thomas from Rochester, MI
Parts Used:: WB36X10003, WB08X10016
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Many months agoI replaced a bulb in the light and it did not work. After swapping bulbs with the light on the other side I determined it was not the bulb.

I asked a handyman at the local fitness center about repairing it and he refered me to your website where I found an exploaded drawing showing the parts I needed and how to get to them. It was great and very easy.

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Bruce from Old Orchard Beach, ME
Parts Used:: WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burned bulb

removed the lens cover with one screw and replaced bulb

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: edward from schererville, IN
Parts Used:: WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

bad bulb

unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.

Was this instruction helpful to you?

Customer:: gerri from north haven, CT
Parts Used:: WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

burnt out bulb /microwave

simply to install new bulb. Unscrewed the under the microwave lamp door with a screwdriver. Inserted new bulb into socket. good to go

Was this instruction helpful to you?

Customer:: william from San Marcos, CA
Parts Used:: WB49X10129
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

broken micro tray

placed plate on carousel

Was this instruction helpful to you?

Customer:: james from panama city, FL
Parts Used:: WB07X11034
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

brokem grill

I replace the grill with a new one.

Was this instruction helpful to you?

Customer:: PATRICIA from ALEXANDRIA, VA
Parts Used:: WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

replace micro/hood combo stove light

simply unscrewed protective lens cover, and swapped bulbs--these bulbs are great--last for years

Was this instruction helpful to you?

Customer:: DAVID from SUGAR HILL, GA
Parts Used:: WB36X10003
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

burn ed out bulbs

I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair

Was this instruction helpful to you?

Customer:: Paula from Camp Hill, PA
Parts Used:: WB06X10596
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Grease filter not cleaned for 7 years !

Threw the old filter away and slide the new one in without any tools ! Filter should be cleaned every month - who knew ?

Was this instruction helpful to you?

Customer:: Karen from Springfield, IL
Parts Used:: WB36X10003, WB08X10016
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Insulator around light socket Broke.

Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.

Was this instruction helpful to you?

Customer:: tom from shelby, NC
Parts Used:: WB36X10003, WB08X10016
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

after 10 years, sockets wore out, got brital

lower hood; support hood with spice rack;angle just right; unscrew light socket; remove wiring harness; replace; connect wiring harness;

Was this instruction helpful to you?

Customer:: George from Arlington, TX
Parts Used:: WB36X10003
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burned out light bulb in the over-stove microwave

Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.

Was this instruction helpful to you?

Customer:: Danny from Zebulon, NC
Parts Used:: WB08X10016
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bulb separated from base, leaving base in socket. Unable to remove base without damaging socket.

Removed 5 phillip screws from bottom plate of microwave oven to lower the plate and gain access to the socket. Then, removed screw(s) attaching socket to the oven. Installed socket, and secured the bottom plate of the oven with screws removed previously.

Was this instruction helpful to you?

JVM1540BMC01 General Electric Microwave - Instructions