RVM225WLC01 General Electric Microwave - Instructions

so easy, but how do i turn light off?

Part recieved next day. thanks so much

Still did not receive any screws with new handle therefore cannot install new handle.

With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

Since the job required replacing both the bulbs and sockets the unit was dropped from the wall. Used a towel and plywood to protect the range under the unit. Then these steps: Unplugged the power cable and placed a support board under the unit while removing three bolts from overhead cabinet. Next, removed support board and with a helper rotated the unit down and lifted it out of the rear wall mounting panel. Then turned the unit upside down, removed the bottom plate and unplugged the feed wires and two wires to each of the sockets. Next the single screws holding the sockets were removed and the sockets extracted from the mounting shells and new units were installed. When remounting the unit it was necessary to start all three bolts from the upper cabinet just a few turns and then tighten the center bolt completely first.

Removed the two screws and old handle. Replace
new handle easily. Great service on receiving part.

removed the lens cover with one screw and replaced bulb

This support hook was a bit different and we hope it will not melt when it is on bake cycle. Had to put the hook in place

Removed old handle, screwed on new handle.

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

used the part I requested and a few extra bolts...job well done!

I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.