PEM31BMC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Billy from SWANNANOA, NC
- Parts Used:
- WB49X10097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old plate got broken
Just open door and install the new cooking tray in the grooves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from E PATCHOGUE, NY
- Parts Used:
- WB06X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Roller stems wore out; rollers fell off
Open door. Remove tray. Remove old roller assembly. Insert new roller assembly. Replace tray. Close door. It took more time and effort to unpack it than it did to replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SAN JOSE, CA
- Parts Used:
- WB27X7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
CERAMIC FUSE BLEW WHILE HEATING VEGETABLES
I found an exploded view diagram of of my microwave model which was very helpful. You need only remove outside metal skin by removing 4 screws on either side and 4 more on the back. Remove 4 plastic hole plugs from the top mounting inserts. Gently pull sides out and lift up and back to remove outer skin. The fuse is located on the back right corner behind the control panel. You access from the side. The fuse is under the spreader bar. Lift fuse up gently to remove.
P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Syracuse, NY
- Parts Used:
- WB06X10723
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
door hinge was loose, appeared to need something to stabilize
I could not do the repair. The clip that I ordered did not go in the bottom hinge, but rather in the top hinge, which was not broken. I could not figure out how to repair it. There was no other part in the diagram that looked as though it would solve the problem, so I needed to buy a new microwave. A more detailed drawing would have been helpful--one that showed how the hinges were attached and how they worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Inverness, IL
- Parts Used:
- WB06X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the rollers on my turntable guide became squared so that the roller wheel would not turn.
I opened the box, took the turntable guide out and put it under the microwave plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Charlotte, NC
- Parts Used:
- WB49X10097
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken plate in microwave
I slipped the new saucer out of the box and placed it in the microwave. I was very disappointed to discover that the new one didn't fly like the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Los Gatos, CA
- Parts Used:
- WB49X10097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke glass plate cooking tray in microwave
New part came -- perfect fit, set it in the microwave, no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ruth from pawleys island, SC
- Parts Used:
- WB06X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost roller turntable guide
Installed new one. I do not know if these rings can be repaired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Bonita, CA
- Parts Used:
- WB27X10585
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Stopped heating and had a banging noise
I took instant pictures at each step to make sure I put the wires back correctly. Removed the front panel. Discharged the capacitor with a voltage meter. Removed parts in front of the magnetron. Removed and replaced the magnetron. Reassembled. Works find now. Small hands, a flashlight and a magnet (for dropped screws) would help. I did not need the pictures.
Was this instruction helpful to you?
Thank you for voting!