JVM1650WHC02 General Electric Microwave - Instructions

Removed five screws from the underside of the mircowave. Disconnected the two prong plug in. Removed the one screw that held the motor and replaced with new motor. Reconnected the plug and replaced the five screws
Tested the result with a bag of microwave popcorn. Worked perfectly.

Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.

Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.

Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)

I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.

Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,

took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.

remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now

unplugged power
removed main black cover.
located part WB24X10047 and replaced

With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!

First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.

Screwed in new bulb.

Told by appliance repair service that parts were very expensive and service call started at $80 minimum. Finding replacement motor on your site was very easy. Instructions on repair were very complete and included pictures of the motor itself which had same capacity as replacement motor. Before ordering part from PartSelect I followed the online instruction for repair/replacement of the Microwave table motor and it was exactly as described. Removed filters and 10 screws with a single Phillips head screw driver. Motor looked the same as picture and ordered it. Part arrived in 24 hours and it took 4 minutes to replace the motor from start to finish. Total costs including shipping was approx 40 dollars. Great service and great site. This is my second repair using PartSelect.

The delivery was lightening fast...which I didn't expect. Great service.

First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.

It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.

And to think GE said to buy a new one!

Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.