JVM1650BBC06 General Electric Microwave - Instructions

First I unpluged the power cord. Then I removed five screws on the bottom panel which will swing down to reveal the turntable motor. I removed the electrical plug from the motor and the two screws that hold the motor in place. Put the new motor in place and align the flat side of the motor shaft with the hole in the bottom of the turntable. Fasten the two screws that hold the motor back in place and reconnect the power plug to the motor. Swing the bottom panel back in place and secure with the five screws. Plug the power cord back in and reset the clock and you are ready to use the microwave.

This was a very simple do-it-yourself repair and information on the partselect website was very helpful. The order and shipping process was simple and fast. Anyone who knows which end of a screwdriver to use should be able to do this repair.

Removed the screws holding the bottom cover on, removed screws holding motor in place, replaced motor, put everything back in. Simple as changing batteries.

The nice thing is that PartSelect, as always, delivered exactly what I needed and very fast. Ordered on a Wednesday and received it on Thursday (the very next day!)

7 screws, lowered the bottom and replaced the motor with two more screws. It was fairly easy and I'm pretty proud of myself.

The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.

Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.

First I removed the 6 screws that hold the bottom of the microwave . I was able to see and get to the cooking tray drive motor. I removed the 2 screws and took out the motor. I replaced the motor and replaced all the screws. Started the microwave and it worked , no problem.

I thought this would be a major project but tured out to be very simple - 7 screws, 10 minutes and done.

The repair was extremely easy. Remove seven screws in the bottom trim, slip the electrical connector off and remove the two screws holding the motor. Slide the new motor into position, replace the connector and screws.

As others have desribed - remove 5 screws from the bottom cover. Lower cover and replace turntable motor with 2 screws.

Told by appliance repair service that parts were very expensive and service call started at $80 minimum. Finding replacement motor on your site was very easy. Instructions on repair were very complete and included pictures of the motor itself which had same capacity as replacement motor. Before ordering part from PartSelect I followed the online instruction for repair/replacement of the Microwave table motor and it was exactly as described. Removed filters and 10 screws with a single Phillips head screw driver. Motor looked the same as picture and ordered it. Part arrived in 24 hours and it took 4 minutes to replace the motor from start to finish. Total costs including shipping was approx 40 dollars. Great service and great site. This is my second repair using PartSelect.

Repair was simple. Remove screws on bottom panel of microwave, let cover hang on hinges. Remove two screws from drive motor, remove old motor, insert new motor, replace two screws, then reattach bottom panel. Done!

Quiet has returned to my microwave:-)

I also discovered that the (night light) bulbs are much easier to replace when the bottom panel is lowered.

The delivery was lightening fast...which I didn't expect. Great service.

First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.

It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.

And to think GE said to buy a new one!

Replace ventilator motor. No problem when you have correct part.
Thanks for the fast service.

Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.

Screwed in new bulb.

took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.