JVM1650BBC06 General Electric Microwave - Instructions

Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.

took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.

Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.

thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)

I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.

Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,

removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again

Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.

I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.

took screws out of bottom of microwave.dropped down bottom cover to get at drive motor I took out one screw droped down cooking tray motor disconnnected 2 wires reconnected put back up and put 1 screw in ,fastened bottom and was fixed very easy ,and parts select is the best place to find what you are looking for if I ever need parts this is where I will order from service is great and only took about 2 days to receive my part .I went to store where I bought my microwave and they wanted to sell me a new one.saved over $200

Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!

This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!

Removed the 5 screws that held the housing so it dropped down. removed the 2 screws to the motor. Disconnedted the plug. reinstalled the new motor. connected the plug and raised the housing and replaced the 5 screws. Took less than 10 minutes start to finish. Piece-of-cake.

removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.