JVM1540WMC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from Walnut Creek, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulb below the over burned out
Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Alexandria, VA
- Parts Used:
- WB06X10468
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hoplders was melted by steam fron burner on stove
self
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ISAAC from MADAWASKA, ME
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Tray
Very easy replacement. Just lift out and replace with a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from shelby, NC
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
after 10 years, sockets wore out, got brital
lower hood; support hood with spice rack;angle just right; unscrew light socket; remove wiring harness; replace; connect wiring harness;
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from STRONGSVILLE, OH
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out microwave light bulb and base broke off in light socket
Replaced light socket and bulb. Real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS from SPRING, TX
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light bulb fused it self to socket
replace socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pines, from Middletown, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from CHEHALIS, WA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no lights
Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from ST PETERSBURG, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Over Stove Light Bulb Out
Took screw holding lens cover out, dropped cover down, unscrewed old bulb, screwed new bulb in socket. Screwed cover back in place. This is the third bulb in this socket, the other bulb is original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Puyallup, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass tray broke in microwave
Removed tray from shipping container and installed in the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from La Crescenta, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Armada, MI
- Parts Used:
- WB26X10208
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable was making horrible noise.
Went on YouTube and found an example of my problem and watched it! That's how I knew which part to order. The part came within two days of ordering and I installed it within 10 minutes. My husband was so proud he told all the guys at work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Arlington, VA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken microwave glass tray
Placed the new tray in the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Camp Hill, PA
- Parts Used:
- WB06X10596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter not cleaned for 7 years !
Threw the old filter away and slide the new one in without any tools ! Filter should be cleaned every month - who knew ?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Springfield, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Insulator around light socket Broke.
Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.
Was this instruction helpful to you?
Thank you for voting!