JVM1429WAC03 General Electric Microwave - Instructions

easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!

First I unplugged the microwave from the wall receptacle. Next I removed eight screws that let the bottom plate of the microwave hood pivot down with its hinges. Next I removed two screws holding the turn motor in place. I then unplugged the motor and replaced it with the new motor and reversed the above procedures until everything was back in place. I then turned the microwave on and was thrilled to find it working properly again.

unplugged the appliance, removed the glass tray from inside, turned the microwave on its side and removed the 3x3 panel, removed the drive motor by taking out two screws and disconnecting the two electrical wires, compared the new item with the old one, placed new in olds position and screwed in place. replaced the 3x3 cover, turned microwave upright, plugged in the power cord, placed a cup of water on the tray, turned the microwave on for 30 sec. and watched the table turn. Very simple and convenient application.

First I unplugged microwave oven, then removed the six screws at the bottom of the microwave and lowered the base to expose the small motor. I removed the motor and replaced it with the new one. From inside the oven I pushed the drive shaft back into the new motor, then replaced the bottom with the six screws. I plugged the oven in and tested it. It worked! In less than 15 min. I saved over $220, and I'm a 65 year old Grandma! Thank you, thank you!

7 screws, lowered the bottom and replaced the motor with two more screws. It was fairly easy and I'm pretty proud of myself.

The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.

Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.

First I removed the 6 screws that hold the bottom of the microwave . I was able to see and get to the cooking tray drive motor. I removed the 2 screws and took out the motor. I replaced the motor and replaced all the screws. Started the microwave and it worked , no problem.

Removed the screws holding the bottom cover on, removed screws holding motor in place, replaced motor, put everything back in. Simple as changing batteries.

The nice thing is that PartSelect, as always, delivered exactly what I needed and very fast. Ordered on a Wednesday and received it on Thursday (the very next day!)

The delivery was lightening fast...which I didn't expect. Great service.

First I shut the circuit breaker off for the microwave.
I then removed the six screws on the full undermount. The motor was visible; it was simple to unscrew the 2 screws on the motor; pulled it away from the wire/plug and disconnected it.

It was just as simple to plug the new motor in, then screw the unit it place with the 2 screws.
That was it...just replaced the undermount and turned the cicuit breaker back on.

And to think GE said to buy a new one!

Told by appliance repair service that parts were very expensive and service call started at $80 minimum. Finding replacement motor on your site was very easy. Instructions on repair were very complete and included pictures of the motor itself which had same capacity as replacement motor. Before ordering part from PartSelect I followed the online instruction for repair/replacement of the Microwave table motor and it was exactly as described. Removed filters and 10 screws with a single Phillips head screw driver. Motor looked the same as picture and ordered it. Part arrived in 24 hours and it took 4 minutes to replace the motor from start to finish. Total costs including shipping was approx 40 dollars. Great service and great site. This is my second repair using PartSelect.

Disconnect the power cord. Removed the screws locate under the spacesaver microwave. The bottom will swing down and hang off the hooks on the back edge. Disconnect the wires plugged into the broken motor. Remove the two screws that hold the broken motor in place. Replace with new motor and re-insert screws and motor wires. Reassemble bottom panel and plug power cord back in.

Removed filter, removed five (5) screws, lowered lower pan, disconected feed wire, removed screw holding the moter, twisted old moter out. Twisted new moter in, replased screw, conected feed wire, closed pan, replased five (5) screws, replaced filter. Tested microwave with glass of water in it.

All went well.

From part order to finish was less then five (5) days.

The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.

Took out the screw holding the old motor, unpluged it and reversed the procedure to install new part. My wife is now very happy!

Repair was simple. Remove screws on bottom panel of microwave, let cover hang on hinges. Remove two screws from drive motor, remove old motor, insert new motor, replace two screws, then reattach bottom panel. Done!

Quiet has returned to my microwave:-)

I also discovered that the (night light) bulbs are much easier to replace when the bottom panel is lowered.

I received the tray and place it in the microwave for a perfect fit. My wife is so happy.