JVM1429CDC01 General Electric Microwave - Instructions

took of cover removed switch and replaced with new one

Found this site, was able to identify the specific part through the internal search engine, very user friendly.

Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!

If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.

Great site, great resource, super fast shipping.

Original coupler was melted on shaft. I couldn't pull off with pliers, so I removed bottom panel, pulled out motor and the pieces of coupler just fell out. I put on the new one - replaced screws and hurray......

PS240270
Ceramic Fuse - 15 Amp
Easy installation , remove microwave cover housing ,locate fuse by door catch & replace..
Received quickly..
Replaced fuse , removed microwave cover housing , located fuse adjacent door catch removed & installed new fuse...

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.

Unpugged microwave. Removed the screws on the bottom cover of the micorwave. Unpugged drive motor and removed two screws from drive motor. Installed new motor and replaced the bottom cover, plugged in microwave . . . presto!

Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.

The replacement of the light no problem, the reason the light broke; problem. The original was glued in (for transport i think) and simply trying to unscrew it out (in a very tight slot) it broke; be careful or you’ll be buying a new $20 bulb (with shipping and handling).

Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.

Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.

It functioned good as new. Relatively cheap and very easy fix.

Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Using the exploded parts view I removed three Philips screws from the lower plate (the screws are located on the front edge of the panel that holds the air filters). Slide the lower panel forward slightly and allow it to swing down. Remove the amphenol connector to the motor and hood lights by pressing the sides of the plastic clip and place the lower panel to one side out of the way. f you intend to clean the lower panel in a dishwasher remove all electrical components before doing so (bend back the clips holding the wires in place and remove the lamps, remove the Philips screws holding the lamp holders); note: these are the only screws with a short shoulder on them, make sure they go back in the same place to hold the lamp holder to prevent damage to the holder). Remove the Philips screw holding the turn table motor in place. Slide the entire motor assembly to one side to allow the motor shaft to slide off the coupler. With the oven door open, remove the old coupling by sliding it to one side to clear the retainer. Insert the new coupling and replace the motor making sure you align the motor shaft with the flat side of the coupling. If you have cleaned the lower assembly in the dishwasher or by hand make sure all parts are dry before reassembly (reinstall the lamp holders and the wiring assembly. Reconnect the amphenol connector (it can only plug in one way by nature of design). Slide the back of the lower assembly into the channel at the back of the oven and replace the three screws holding the lower panel in place.
Now you have saved your self the cost of a service call or possibly a new microwave you can use this as supporting evidence that you can afford the new 20" monitor for your PC. Test out the repair and make your spouse a cup of hot coffee or cocoa to brag on yourself and make your sales pitch.