HVM1750WMC01 General Electric Microwave - Instructions

so easy, but how do i turn light off?

Part recieved next day. thanks so much

My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

I asked a handyman at the local fitness center about repairing it and he refered me to your website where I found an exploaded drawing showing the parts I needed and how to get to them. It was great and very easy.

With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

Since the job required replacing both the bulbs and sockets the unit was dropped from the wall. Used a towel and plywood to protect the range under the unit. Then these steps: Unplugged the power cable and placed a support board under the unit while removing three bolts from overhead cabinet. Next, removed support board and with a helper rotated the unit down and lifted it out of the rear wall mounting panel. Then turned the unit upside down, removed the bottom plate and unplugged the feed wires and two wires to each of the sockets. Next the single screws holding the sockets were removed and the sockets extracted from the mounting shells and new units were installed. When remounting the unit it was necessary to start all three bolts from the upper cabinet just a few turns and then tighten the center bolt completely first.

removed the lens cover with one screw and replaced bulb

Decided best way to repair was replace the whole door. Yes it was a pricy repair, however I did not want the landlord to find out. I placed the old door with shattered glass pieces taped up in the box and disposed of properly and no mess.

Not hard to replace for a aircraft mechice

I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

Had to take the MW off the wall, remove the cover, and find the magnetron. Issue was the HV-capacitor. Had to remove the diode and capacitor to discharge the capacitor safely. Crackle-Bang! Then put it back before toying with the HV-transformer in order to get the magnetron out. Took a little under two hours to get it back on the wall and a lot of cajones when monkeying around the chassis removing the capacitor. Not a job for most everyone as this was a potentially high-shock repair due to the voltage and micro-farads held in that capacitor. Hardest part was getting the magnetron to drop out past the HV-transformer. Also, the thermostat had to be removed from the magnetron and re attached to the new one. Fiddly delicate job, not for the clumsy or faint of heart.

Removed the bottom plate screws from the microwave. Disconnect the wire harness. Replacement of the light sockets is easy. The female terminal connectors that connected to the bulb sockets were corroded, so I had to go to the hardware store and get replacements for those also. Replacement of those was unexpected but straightforward.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

Placed the new tray in the microwave.

Fist I removed the 5 screws under the microwave. Then I dropped the panel and accessed the socket. I removed the socket by removing the one screw and disconnecting the wires. Replaced the wires on the new socket, installed the new bulb and reattached with the screw. replaced the panel with the 5 screws and I was done. Easy