JVM1630CJ02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from PIEDMONT, CA
- Parts Used:
- WB26X32629
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
runs but does not heat
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from SPRING, TX
- Parts Used:
- WB49X10176
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken glass turntable
I was surprised to find that the turntable for my 10 year old GE Profile microwave/convection oven was not readily available at my local GE retailer. I ordered the part from this website hoping that my order would be filled. I received an immediate response from customer service and the part was on my front doorstep in under 1 week! I would order from this website again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tarpon Springs, FL
- Parts Used:
- WB36X10328
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior lamp burned out
Unscrewed the vent at top of microwave exposing small access to bulb. The access to this was very limited so that was the major issue in changing the bulb. You needed small hands to do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Smithton, IL
- Parts Used:
- WB06X10689
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels would not stay on old ring
Removed turn table,removed old ring,put new one in its place, Put turntable back in and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenoma from NORTHGLENN, CO
- Parts Used:
- WB02X11096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Latch was broken you put spring on
Took off plastic around inside the door , took broken latch off and put spring on new latch on plactic on and it works . ????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry Totten from GROVES, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Opened door to get food put more food in closed door it wouldnt work
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a new one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.
My micro is only 2 years old so I was hoping it wasn't anything major.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Kinnelon, NJ
- Parts Used:
- WB55X10816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broke off (actually the frame broke)
Ordered new frame. Snapped the old frame off, transfered glass to new frame. Popped new frame on micro door. Attached handles threw the holes through metal flanges on door. didn't need instructions. Very logical.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda sklar from JAMAICA PLAIN, MA
- Parts Used:
- WB49X10176
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Broken glass turntable in microwave
Just placed it in microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from KEY WEST, FL
- Parts Used:
- WB02X35607
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Remove and replace charcoal filter
Open microwave door and remove plastic cover running across top of the oven box by unscrewing 3 Phillips head screws above and behind plastic cover. (4th screw to the right is not related to this cover). DO NOT PULL COVER STRAIGHT OUT. Cover slides either right or left then pops out. Remove old filter and replace and reinstall cover. Filter lays at a 45 degree angle against metal tabs tilting toward you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florentino from West Palm Beach, FL
- Parts Used:
- WB21X10148
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Power
Check with Digital meter all connections.Find a Thermostat open loop.This thermostat is near the Megatron .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Bessemer, MI
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
mICROWAVE WOULD NOT HEAT
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from NORTH PORT, FL
- Parts Used:
- WB02X35607
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace charcoal filter
open microwave door remove 3 screws on top of microwave, slide top panel to the left and pull out top panel slide old filter out put in new one and reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debora from Saugus, MA
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Too dirty to clean, bought new parts.
I had already removed the old grease filters. Unwrapped the new grease filters and popped into place. No tools were necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alicia from ORANGE, CA
- Parts Used:
- WB07X10969
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I had broken the clips that hold the vent in while cleaning it.
I ordered the part from this site (which was a little lower cost than another site but was described as a genuine GE part), and I looked up the instructions in my manual. It took about a week to get the new grille. There are 2 philips head screws attaching the grille. Just remove the screws, discard the old grille and put in the new grille with the same screws. The description on-line calls it a snap on grill which is a little misleading. It is attached with screws. I was fearful that it would not fit but it is identical to the old one. I am very pleased I did not have to replace the microwave even though it is 11 years old, it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!