JVM6175RF1SS General Electric Microwave - Instructions

First, there are three door operated switches in this model. The monitor sw, the secondary sw (both of these are on the bottom in the same bracket) and the door sensing sw on top. The door sensing and secondary switches are both N.O. and have the same part number (probably why you show just two switches). The monitor sw is N.C. and it was not my problem. The secondary sw was bad on my oven but I had replaced the door sensing sw (which wasn't bad) on a previous order and kept the old one so I used it to make the repair. All three switches can be accessed without removing the oven by removing the discharge louver (remove two flat head screws on top and slide the louver to the left) then carefully remove the control panel (one screw on top and lift out). The switches are held in place by a plastic tongue that fits into the rear mounting hole on the switch. I used a common screw driver with a small tip to gently lift the tongue and slide the switch out with needle nose pliers. The new switch just snaps back in. The switch holder bracket looks like it would be easily broken so be gentle. I don't know what the symptoms would be if either of the other switches were bad so I would recommend buying all three and you would have them if one of the others failed in the future. The information I gave on the switches came from a schematic I found inside the control box. Hope this is helpful.

Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.

I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

easily replaced. parts arrived quicker than suggested. thanks

lower hood; support hood with spice rack;angle just right; unscrew light socket; remove wiring harness; replace; connect wiring harness;

Very simple disconnect light socket unit from snap in power supply replace socket with bulb screwed in reattach & back in business. Your service in supplying needed parts was par excellence. Thanks again

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

Replaced light socket and bulb. Real easy repair.

simply to install new bulb. Unscrewed the under the microwave lamp door with a screwdriver. Inserted new bulb into socket. good to go

Threw the old filter away and slide the new one in without any tools ! Filter should be cleaned every month - who knew ?

Took screw holding lens cover out, dropped cover down, unscrewed old bulb, screwed new bulb in socket. Screwed cover back in place. This is the third bulb in this socket, the other bulb is original.