DVM7195EK1ES General Electric Microwave - Instructions

replace tray

I ended up breaking one bulb trying to remove a burnt bulb for replacement. We then tried removing the other bulb and it wouldn't come out either. I googled the problem and found PartSelect and an explaination of the problem. Heat from either the stove or the bulbs had fused the bulbs into the sockets. Comments on the problem explained that you just remove the bottome pannel (we had seven screws), unplug the old sockets, insert the new and new bulbs and reattach the panel. It was quick and no problems to correct. We did discover the microwave was on its own breaker, make sure to disconnect or cutoff power to the microwave before you start.

Extremely easy. Less then 10 minutes tops.
Remove the screw holding the cover to the lights.
Remove the burned out bulb(s) (they may give a little resistance).
Carefully line up the holes for the prongs on the bulbs.
Insert the prongs firmly but gently using the styrofoam holders the bulb(s) was/were shipped in so as not to touch the bulb(s) with your fingers.
Replace the screw to the light cover.
Turn on the lights and give yourself a pat on the back.

This was a super easy repair job. I couldn't figure out how the lens that covered the light bulb would have cracked and realized it must have been from my contractor when he replaced my stove. I can't prove it, of course, so I am left doing the repairs. The website was very easy to order from and confirm that I had the correct parts as the model numbers tend to change over time.

Loosen screw holding glass cover plate in place over bulb. Glass cover plate will swing down. Unscrew bad bulb, replace with good bulb, reset glass cover and tighten screw.

This did not fix my problem. I've ordered a new microwave.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.

The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

Went to onlin source, found a couple youtube videos then went to the GE site which had a not-too-easy that find trouble shooting guide. It was extremely helpful as it described a fuse as a fix 80% of the time for touch paid failure. I really didn't believe it would b a fuse, but it was the cheapest fix, $8. I got the fuse and was surprised to fine there are two of them on this model. I took a guess and replaced the top one ( neither fuse was black or burned to indicate a failure but the top one was a bit mor greyish). put it all back together and it works fine.

took off upper grille and touch pad and removed the old line fuse and replaced with a new fuse ...turned on it is working fine...sources of help: UTube and GE manuel

Open the box.. unwraped excessive bubble wrap.. placed in microwave.. Did'nt even break a sweat..

All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again