CEB1590SS3SS General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Roswell, GA
- Parts Used:
- WB36X10131
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Microwave light failed
I needed to remove the front fascia plate and remove the microwave from the cabinet. Then I had to remove the microwave cover. This entailed some difficulty because GE used special screw heads to discourage people from fixing their own appliances. Then, I had to find the bulb fixture and that also was difficult and not obvious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry Totten from GROVES, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Opened door to get food put more food in closed door it wouldnt work
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a new one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.
My micro is only 2 years old so I was hoping it wasn't anything major.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from PIEDMONT, CA
- Parts Used:
- WB26X32629
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
runs but does not heat
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from WEST PALM BCH, FL
- Parts Used:
- WB06X10564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable Coupler had been broken off, by previous owner.
I just matched the prong in the turntable hole and coupler fit into the hole perfectly. All The Best.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patty from SEATTLE, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the glass circular tray inside had cracked in half.It was of no use. I reordered another
The tray came within 5 days and I simply took it out of its well-packaged box and slipped it into my microwave. It is working just like new. I can't thank you all for being so punctual and reliable. better than having to buy a brand new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florentino from West Palm Beach, FL
- Parts Used:
- WB21X10148
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Power
Check with Digital meter all connections.Find a Thermostat open loop.This thermostat is near the Megatron .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Bessemer, MI
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
mICROWAVE WOULD NOT HEAT
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from FREDERICKSBRG, VA
- Parts Used:
- WB06X10564
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The microwave had been mistakenly turned on with nothing in it and the turntable coupler was badly burned. Pieces of it eventually broke off.
The burned remnant of the coupler was a bit difficult to remove. I did so with a pliers and also used the pliers to clear out some burned fragments of the coupler. With a flashlight I determined that the slot for the coupler was now clear. I matched the configuration of the slot with that of the new coupler and it slid immediately into place with no difficulty whatever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from COVINGTON, LA
- Parts Used:
- WB36X10131
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Interior light burned out.
Removed back screws, pulled cabinet off from the rear, unplugged lamp on upper right side in front reattached two wires, replaced 1 screw to hold lamp in place, reinstalled cabinet and done.
Actually followed prior instructions on your site. Spot on.
Actually followed prior instructions on your site. Spot on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Celia from Yorba Linda, CA
- Parts Used:
- WB48X10073
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing shelf
I am so glad I found this web site. I ordered the shelf and now I can use my microwave as a convection oven.
The ordering was simple and the delivery was quick. Thank you so much partselect.com
The ordering was simple and the delivery was quick. Thank you so much partselect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from DENVER, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from BRYSON CITY, NC
- Parts Used:
- WB48X10073
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
For $82.00 dollars I did not expect a piece of equipment that at best might be worth $10.00, including shipping. It was so poorly made in Korea that if you picked it up with your bare hands you are in danger of cutting your fingers on the rough edges. For $82.00 I did not ecpect such a poorly made
The rack is essential for the operation of the GE microwave combination oven if it is to be operated as a convection oven or when using it in the combination mode. I hope I will never need another part. If I do I will seek a company with better prices and better made parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from ROSSFORD, OH
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Placed the new tray into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Portland, OR
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass tray somehow got a nick in the edge, a few days later it split while in use.
Another company said the new plate would arrive in mid-March, this company seemed to be faster so ordered the tray here, and it came in less than a week. I put the turn button back in the center hole, set the wheeled ring on the bottom of the oven, fitted the new glass tray onto the turn button.
Was this instruction helpful to you?
Thank you for voting!