JES1034WF02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jan from North Las Vegas, NV
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I dropped the glass tray
My husband wanted to use super glue to put it back together. I totally disagreed - googled the problem - order the replacement tray. It works great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Basking Ridge, NJ
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
threw away broken glasss tray and put in new one
with one hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Crystal Spring, PA
- Parts Used:
- WB39X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
the glass tray was broken in a move
just set the new carousel tray into place inside the microwave.
but your site made it so easy to order. will keep the site as a favorites.
thank you
but your site made it so easy to order. will keep the site as a favorites.
thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven wouldn't heat
remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Butch from Gulfport, MS
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Started with a burning smell and eventually no operation at all.
Took the screws out that held the oven case on. Looked around and found a connection on the oven cavity thermal cut out the plastic melted and black looking. I knew this was the problem but I checked the fuse anyway and the fuse was good, so I ordered the part from part select and they shipped it out fast and now my microwave is working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Mountain View, AR
- Parts Used:
- WB24X829
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave worked but oven fan came on when door was opened - should onlly come on when oven is operating.
Removed the microwave with the buit in housing from the cabinet. Removed microwave from built in housing. Removed outer cabinet giving access to remove control panel and smart board where switches are located. Removed control panel to get to smartboard. Removed smart board after disconnecting a few wires to allow easy removal. Individually removed and then tested each switch using multimeter. Found seondary Door Switch (bottom of smart board) operation to be intermittent (switch trip button extremely loose and rattle inside this particular switch) Ordered replacement part which came very quickly on standard shipping order. Put new switch on smart board and remounted, reinstalled control panel and reconnected various wire connectors previously disconnected. Then plugged in oven and tested for opertation - didn't work at all! But, after bleeding off capacior charge by removing connectors and discharging capacitor to ground, then reassembling control board and smart board into oven, then trying agian, it has worked perfectly ever since. Do not understand why capacitor disconnect/discharge was required but suspect this reset the control electronics. Easy fix and hope to get another 12 years out of this appliance which is used multiple times every day. Also have two other identical micorwave ovens, one is 20 years old, but these get used relatively infrequently.
Was this instruction helpful to you?
Thank you for voting!
Microwave came on when door open
Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Middleburg Hts, OH
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No display
I had a bad cut off sensor on oven cavity I ran the Microwave with nothing in it and it smoked I ran it for another 6 months then 1 day I was heating water and it stop- working. I put a new tube in might be Okay but I was not going to risk it taking another cut off sensor on overload. You have to change sensor and put on a new tube. Clearly it would be cheaper to buy a new unit but it was only 2 years old and I am an old tech and was curious. The sensor cost only 16 bucks new tube about 55 a replace brand new oven 81 bucks there you have it I was stubborn and going to get that sucker back into operation I had another oven go out the same way
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NJ
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Coupeville, WA
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Cavity Thermal Cutout Open
Remove cover-the hardest part, as I needed to buy a new set of driver bits that included the dimpled security drivers to remove three screws. GE includes schematic and troubleshooting flow chart with the unit, taped inside the cover. Required more time to look up the part on-line and order it than time used to make the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Lexington Park, MD
- Parts Used:
- WB27X10985
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would not turn on
I removed the cover this required a special star Apex tip witha hole in the center. $10 for a set at Lowes.Replaced the fuse and Thermal cut out at the same time. The oven woks like a charm.I would like to add that GE customer service was no help basically told me that it was a throw away unit. If they built it you can fix it.Hope this helps any DIY breathern outthere.
Was this instruction helpful to you?
Thank you for voting!