JES1034WF02 General Electric Microwave - Instructions

Per the troubleshooting diagram inside the microwave oven, I discovered the one of the TCO was open (using Ohmmeter). Found my microwave oven model on PartSelect and used the diagram to select the TCO needed and placed order. Part came in three days, installed new TCO, reconnected wires and the microwave oven was back working in 10 minutes.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

must of had loose connection from wire terminal
to thermostat from factory. thermostat and wires
were melted. removed thermostat. and cut burnt
wires back. replaced thermostat and terminals.
used better quality terminals than factory.
also checked and tightened other loose connections. there was enough wire left after cut back to just put on new terminals.

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

Took the cover off (removed the five screws, two of which were security screws off the back) and found one connector on the thermal cut out with its shielding melted. Very easy swap out of the new cut out and we were up and running as if new.

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

this is not fair to the do it yourself person because I have been an electrican for forty one years I removed the cover spotted the burnt limit switch ordered the part replaced the part and checked operation of the microwave thanks for the painless task of locating and ordering of needed part

This is sometimes described in other repair notes as "microwave 'runs' when door is open."
With power disconnected: Remove the microwave's metal grill surround. Three lower screws accessible with lower oven door open. Two screws accessible at top of microwave door opening with door open.
Remove microwave control panel: Remove two femaleTorx head screws (#27?) that secure the panel, accessible at right side of door opening. The right side of the control panel is secured by plastic tabs fitting into slots in the oven frame. Take good care to note how these tabs disengage from the slots (lift and shift). Tab breakage very possible! Once disengaged, the panel hinges outward and downward and is self-supported. It may be necessary to guide some of the wiring out of the way to fully lower.
There are three door switches, one "monitor" and two "secondary" switches. All switches are housed in a plastic frame, which must be lifted out of position for access, each switch is retained by flexible plastic, breakable-looking hooked fingers. Also note that the electrical connectors have tiny release tabs that must be depressed in order to pull them off of the switches. In my case the topmost switch, one of the "secondary" switches, was clearly bad since there was no "snap" or click when pressing the switch's button. Maybe you can determine which switch is bad before proceeding but I had ordered all three to avoid going through this exercise again any time soon.
Replace switch or switches, place switch carrier back into position and otherwise reverse the disassembly steps.

I thought I was setting the timer only on the microwave and accidently cooked an empty oven for 10 minutes. It was dead and I used the schematic and figured out the problem. Got the part and installed in 10 or less minutes. Oven is back in action.

Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .