JVM1870BF02 General Electric Microwave - Instructions

I placed the glasstop on the sprocket

Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.

I took the part out of the box and handed it to my wife and said "here ya go hun, go put this under the glass turntable in the microwave. You'll know it's installed when you hear it click down" She yelled back, "easy as pie" - - - Humm.. I can't make a pie. Fortunately the old one was in one piece as the side just split so it slid off very easy. The new one just snapped in place.

I unscrewed two screws on top of the microwave, slid the part (which opens when the microwave is in use) to the left and put it aside. The old filter is then easily picked up and removed. I placed the new filter in the same spot. I repositioned the removed part in place, lining up the little tabs, slid it to the right, which automatically lined up for replacement of the screws. These directions were included with the new filter and it was very easy to follow. I can't believe anyone would pay someone else to do this simple task! I am a 67 year old female.

Just removed the screws from botton of unit, unplugged and removed the burned up motor, reveresed the process to install new motor. Less than 10 minute job.

unsrewed the bottom of the microwave(there was about five or six screws)located the motor unpluged it and unscrewed the two screws holding the motor once installed i reversed the proceedure and put everything back together...simple as 1,2,3...

Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward

I finally found the two screws to remove the fan opening. Once I did that I did not locate an OLD charcoal filter!! I just deducted there was never one in there, based on where the instructions said it should be located. I placed the new filter and let it "rest on an angle" as per the instructions I read from the diagram, and from the other peoples description online. I put the breaker back on and all seems fine!

ha to remove the bottom ,to get at the internal screws that held the drive motor. after disconnecting the power to the moter, i removed the two screws that held it in place. i installed thre new motor , reconnected the wire plug to motor . replaced the outer screws, and the project was done.

Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

I removed the screws (7) around perimeter of bottom. Don't remove the middle screw as it holds some gizmo in place. Dropped down hinged bottom. Removed motor (2 screws and a plug) matched to picture on website and ordered.

2 days later, part arrived, installed, good to go.

Bill, Kentucky

Unplugged microwave from the wall. Removed the screws on the bottom of the oven. Detached the light, removed the bottom panel. Unscrewed one more screw on the turn table motor and twisted to remove. Plugged in the new one and reattached the Electrical wires and bottom panel. Piece of cake. Just don't forget to reconnect the lights!