JVM1630CD003 General Electric Microwave - Instructions

I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.

I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.

removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel

Removed 5 screws to allow lower pan to hang down. Unplug motor, remove 2 more screws that hold motor in and pull it out. and reverse process for reinstallation of new motor. Took all of 4 minutes allowing time to drink a beer while taking the new motor out of the box

First I removed the 6 screws that hold the bottom panel in place. I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then connected the two wires to the new element. Secured the element in place and replaced bottom panel.

Real simple process!
Thanks!

Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!

I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.

Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,

This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!

took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.

Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.

Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.

Removed old film, installed new horizontally and pulled it downward (match it along the top first). The cover required 2 "hooks" to be removed, only needed 4 clips. Used a screwdriver to remove the 2 clips.

Using a phillips screwdriver, remove 7 screws from the unerpanel of the Spacesaver Microwave. The panel will swing down from the rear edge hinge, exposing the lights and the stirrer motor. Remove the electrical connector and two screws holding the motor in place and remove the motor. The stirrer inside the oven can then be removed if desired. Install the new motor in reverse order. Note rotate the stirrer inside the oven to align the motor shaft to facilitate assembly.

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!