EMO3000HWW03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from Blakely, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My turntable stopped working
I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Raleigh, NC
- Parts Used:
- WB06X10420
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable motor burnt out
lowered bottom panel, unpluged turntable motor, unscrewed one screw. replaced old motor with new alinged turntable button. repluged motor wire and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from oak lawn, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
G.E. microwave turn table was loud and not working
I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sam from edmond, OK
- Parts Used:
- WB06X10224
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken rack holder
removed the damaged / broken rack holder. inserted the new rack holder.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- todd from clinton, IL
- Parts Used:
- WB06X10420, WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable in microwave stopped
First I removed the 5 screws holding the vents and lights on the range hood. Dropped down the panel to the range top. Removed power connector on drive motor and checked for voltage when microwave was running. I had the required 21 vac for the motor to run. Tried to remove motor the hard way and found a screw on the back side after trying to remove the tray hub and broke it because there is tab on it. With the screew holding the removed the motor came right out and the hub did not need to removed. The new parts slipped right in. Thanks for your very quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Fort Stewart, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave noisey
Removed 5 screws to allow lower pan to hang down. Unplug motor, remove 2 more screws that hold motor in and pull it out. and reverse process for reinstallation of new motor. Took all of 4 minutes allowing time to drink a beer while taking the new motor out of the box
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Colorado Springs, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass cooking tray not turning
First I removed the 6 screws that hold the bottom panel in place. I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then connected the two wires to the new element. Secured the element in place and replaced bottom panel.
Real simple process!
Thanks!
Real simple process!
Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from GRAND BAY, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Glass Cooking Table Not Turning - Food Burning
Most mirco wave have a plate on the bottom to protect turn table motor. This one had no screws - it has 6 tabs holding the protective cover. Used pliers to tear tabs. Used philip's driver to remove screw and turned motor to come out. Went back in reverse order replacing motor. Left protective plate off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olathe, KS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not turn
Removed five screws from the underside of the mircowave. Disconnected the two prong plug in. Removed the one screw that held the motor and replaced with new motor. Reconnected the plug and replaced the five screws
Tested the result with a bag of microwave popcorn. Worked perfectly.
Tested the result with a bag of microwave popcorn. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Sparta, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the glass cooking tray would no longer move.
We removed the vents from under the bottom and then the 4 screws and pulled the motor out. It was a no brainer to fix and the part came in alot faster than expected.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Mt. Juliet, TN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive motor dead
This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from Milton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Excessive noise while driving the glass tray.
Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Irvine, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not rotate
removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel
Was this instruction helpful to you?
Thank you for voting!